Diagnostic Instructions
| • | Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure. |
| • | Review Strategy Based Diagnosis for an overview of the diagnostic approach. |
| • | Diagnostic Procedure Instructions provide an overview of each diagnostic category. |
DTC Descriptors
DTC P0403: Exhaust Gas Recirculation (EGR) Solenoid Control CircuitDTC P0489: Exhaust Gas Recirculation (EGR) Solenoid Control Circuit Low Voltage
DTC P0490: Exhaust Gas Recirculation (EGR) Solenoid Control Circuit High Voltage
Diagnostic Fault Information
Circuit | Short to Ground | Open/High Resistance | Short to Voltage | Signal Performance |
|---|---|---|---|---|
Ignition 1 Voltage | P0340, P0342, P0458, P0489 | P0403 | -- | -- |
Solenoid Control | P0406, P0489 | P0403 | P0490 | P0404 |
5-Volt Reference | P0106, P0405, P2122, P2138 | P0405 | -- | -- |
EGR Position Sensor Signal | P0405 | P0405 | P0406 | P0404 |
Low Reference | -- | P0406 | -- | -- |
Typical Scan Tool Data
Circuit | Short to Ground | Open | Short to Voltage |
|---|---|---|---|
Operating Conditions: Engine operating in Closed Loop Parameter Normal Range: 0-4% | |||
Ignition 1 Voltage | -- | -- | -- |
Solenoid Control | 99% | -- | -- |
5-Volt Reference | 0% | 0% | 99%¹ |
EGR Position Sensor Signal | 0% | 0% | 99%¹ |
Low Reference | -- | 0% | -- |
¹ Internal ECM damage may occur if the circuit is shorted to B+. | |||
Circuit Description
Voltage is provided to the exhaust gas recirculation (EGR) valve by the ignition 1 voltage circuit through a fuse. Ground is provided to the EGR valve on the control circuit by a low side driver within the engine control module (ECM). The ECM monitors the voltage on the control circuit of the EGR valve to determine if a failure is present.
The ECM monitors the position of the EGR valve through the EGR valve position sensor. The EGR valve position sensor sends a feedback voltage on the signal circuit to the ECM. The EGR position sensor voltage varies depending on the position of the EGR valve.
The EGR valve utilizes the following circuits:
| • | An ignition 1 voltage circuit |
| • | A control circuit |
| • | A 5-volt reference circuit |
| • | A signal circuit |
| • | A low reference circuit |
Conditions for Running the DTC
| • | The engine is running. |
| • | The DTCs run continuously when the above condition is met. |
Conditions for Setting the DTC
P0403
The ECM detects an open on the EGR solenoid control circuit.
P0489
The ECM detects a short to ground on the EGR solenoid control circuit.
P0490
The ECM detects a short to voltage on the EGR solenoid control circuit
Action Taken When the DTC Sets
DTC P0403, P0489, and P0490 are Type B DTCs.
Conditions for Clearing the MIL/DTC
DTC P0403, P0489, and P0490 are Type B DTCs.
Reference Information
Schematic Reference
Connector End View Reference
Description and Operation
Exhaust Gas Recirculation (EGR) System Description
Electrical Information Reference
DTC Type Reference
Powertrain Diagnostic Trouble Code (DTC) Type Definitions
Scan Tool Reference
Circuit/System Verification
- Ignition ON, observe the scan tool Actual EGR position parameter while commanding the EGR valve ON and OFF. The reading should change from 0 percent to 99 percent with each command.
- If the vehicle passes the Circuit/System Verification test, then operate the vehicle within the conditions for running the DTC. You may also operate the vehicle within the conditions that are captured in the Freeze Frame/Failure Records List.
Circuit/System Testing
- Ignition OFF, disconnect the harness connector at the EGR valve.
- Ignition ON, verify a test lamp illuminates between the ignition 1 voltage circuit and ground.
- Ignition OFF, verify a test lamp does not illuminate between the control circuit and B+.
- Ignition ON, command the EGR valveON and OFF with a scan tool, The test lamp should illuminate.
- If all circuits test normal, test or replace the EGR valve.
| ⇒ | If the test lamp does not illuminate, test the ignition 1 voltage circuit for a short to ground or an open/high resistance. If the circuit tests normal and the ignition 1 voltage circuit fuse is open, test all components connected to the ignition 1 voltage circuit and replace as necessary. |
| ⇒ | If test lamp illuminates, test the control circuit for a short to ground. If the circuit tests normal, replace the ECM. |
| ⇒ | If test lamp does not illuminate, test the control circuit for a short to voltage or an open/high resistance. If the circuit tests normal, replace the ECM. |
Component Testing
- Ignition OFF, disconnect the harness connector at the EGR valve.
- Test for 6-10 ohms of resistance between the ignition 1 voltage circuit terminal and the control circuit terminal of the EGR valve.
| ⇒ | If not within the specified range, replace the EGR valve. |
Repair Instructions
Perform the Diagnostic Repair Verification after completing the diagnostic procedure.
| • | Control Module References for ECM replacement, setup, and programming |
