Crankshaft Rear Oil Seal and Housing Replacement Housing

Important: Do not remove the crankshaft rear oil seal housing if only replacing the crankshaft rear oil seal.

1. Remove the engine oil pan. Refer to Oil Pan Replacement .
2. Remove the transmission assembly.

•	Refer to Transmission Replacement in Manual Transmission - NV 3500

•	Refer to Transmission Replacement in Automatic Transmission - 4L60-E.

3. Remove the engine flywheel. Refer to Engine Flywheel Replacement .
4. Remove the three bolts and the one nut holding the crankshaft rear oil seal housing to the engine.
5. Remove the crankshaft rear oil seal housing.



6. Remove and discard the crankshaft rear oil seal housing gasket.
7. Clean all sealing surfaces.
8. Inspect the crankshaft rear oil seal housing for warping, cracks, wear, or damage.

1. Install a NEW crankshaft rear oil seal housing gasket.




Important: When installing a NEW crankshaft rear oil seal housing the crankshaft rear oil seal will come with the housing. Use the following procedure. Refer to Crankshaft Rear Oil Seal and Housing Replacement if reusing the crankshaft rear oil seal housing.

2. Install the NEW crankshaft rear oil seal housing with the crankshaft rear oil seal to the engine block using the following procedure.

Important: Do not oil or grease the crankshaft rear oil seal lip.

2.1.	Leave the sleeve in the crankshaft rear oil seal and use the sleeve as a guide to ease the seal lip over the end of the crankshaft.

2.2.	Push the crankshaft rear oil seal housing with the crankshaft rear oil seal, fully onto the crankshaft until the housing is against the gasket and the engine.

Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

3. Install the three bolts and the one nut to the crankshaft rear oil seal housing.

Tighten
Tighten the crankshaft rear oil seal housing bolts and nut to 12 N·m (106 lb in).

4. Install the engine flywheel. Refer to Engine Flywheel Replacement .
5. Install the transmission assembly.

•	Refer to Transmission Replacement in Manual Transmission - NV 3500.

•	Refer to Transmission Replacement in Automatic Transmission - 4L60-E.

6. Install the oil pan. Refer to Oil Pan Replacement .

Crankshaft Rear Oil Seal and Housing Replacement Seal

1. Remove the transmission assembly.

•	Refer to Transmission Replacement in Manual Transmission - NV 3500.

•	Refer to Transmission Replacement in Automatic Transmission - 4L60-E.

2. Remove the flywheel. Refer to Engine Flywheel Replacement .
3. Remove the crankshaft rear oil seal from the crankshaft rear oil seal housing.

Insert a suitable tool into the access notches and then carefully pry the crankshaft rear oil seal from the crankshaft rear oil seal housing.

4. Discard the crankshaft rear oil seal.

Tools Required

J 35621-B Rear Seal Installer

Important: Do not oil or grease the crankshaft rear oil seal lip or the crankshaft.

1. Use the J 35621-B in order to install the NEW crankshaft rear oil seal. Refer to Crankshaft Rear Oil Seal and Housing Installation
2. Install the engine flywheel. Refer to Engine Flywheel Replacement .
3. Install the transmission assembly.

•	Refer to Transmission Replacement in Manual Transmission - NV 3500.

•	Refer to Transmission Replacement in Automatic Transmission - 4L60-E.