GM Service Manual Online
For 1990-2009 cars only

Circuit Description

The throttle actuator control (TAC) motor is controlled by the powertrain control module (PCM). The DC motor located in the throttle body drives the throttle plate. In order to decrease idle speed, the PCM commands the throttle closed reducing air flow into the engine and the idle speed decreases. In order to increase idle speed, the PCM commands the throttle plate open allowing more air to pass the throttle plate. If the actual idle RPM does not match the desired idle RPM within a calibrated time, this DTC sets.

Conditions for Running the DTC

    • DTCs P0068, P0107, P0108, P0112, P0113, P0117, P0118, P0120, P0121, P0125, P0130, P0171, P0172, P0201, P0202, P0203, P0204, P0205, P0220, P0300, P0336, P0442, P0446, P0452, P0453, P0455, P0641, P0651, P1516, P2101, P2135, P2176 are not set.
    • The engine is operating for at least 40 seconds.
    • The engine coolant temperature (ECT) is more than -7°C (+19.4°F).
    • The intake air temperature (IAT) is more than -7°C (+19.4°F).
    • The barometric pressure (BARO) is more than 75 kPa.
    • The system voltage is between 11-18 volts.

Conditions for Setting the DTC

    • The actual idle speed is approximately 150 RPM greater than the desired idle speed.
    • The above condition is present for 15 seconds.

Action Taken When the DTC Sets

    • The control module illuminates the malfunction indicator lamp (MIL) when the diagnostic runs and fails.
    • The control module records the operating conditions at the time the diagnostic fails. The control module stores this information in the Freeze Frame/Failure Records.

Conditions for Clearing the MIL/DTC

    • The control module turns OFF the malfunction indicator lamp (MIL) after 3 consecutive ignition cycles that the diagnostic runs and does not fail.
    • A current DTC, Last Test Failed, clears when the diagnostic runs and passes.
    • A history DTC clears after 40 consecutive warm-up cycles, if no failures are reported by this or any other emission related diagnostic.
    • Clear the MIL and the DTC with a scan tool.

Test Description

The number below refers to the step number on the diagnostic table.

  1. This test determines whether the engine can achieve the commanded RPM. If the engine does not reach the commanded RPMs, the test determines whether the RPM is too high or too low.

Step

Action

Yes

No

Schematic Reference: Engine Controls Schematics

Connector End View Reference: Powertrain Control Module Connector End Views or Engine Controls Connector End Views

1

Did you perform the Diagnostic System Check - Engine Controls?

Go to Step 2

Go to Diagnostic System Check - Engine Controls

2

  1. Start the engine.
  2. Command the engine speed up to 1,500 RPM, down to 500 RPM, and up to 1,500 RPM with a scan tool.
  3. Exit the RPM control function.

Does the engine speed correspond within 150 RPM with each command?

Go to Intermittent Conditions

Go to Step 3

3

Inspect for the following conditions:

    • Vacuum Leaks
    • Excessive deposits in the throttle body
    • A faulty positive crankcase ventilation (PCV) valve

Did you find and correct the condition?

Go to Step 4

--

4

  1. Clear the DTCs with a scan tool.
  2. Turn OFF the ignition for 30 seconds.
  3. Start the engine.
  4. Operate the vehicle within the Conditions for Running the DTC. You may also operate the vehicle within the conditions that you observed from the Freeze Frame/Failure Records.

Did the DTC fail this ignition?

Go to Step 2

Go to Step 5

5

Observe the Capture Info with a scan tool.

Are there any DTCs that have not been diagnosed?

Go to Diagnostic Trouble Code (DTC) List

System OK