Circuit Description
The powertrain control module (PCM) supplies a bias voltage of about 450 mV between the heated oxygen sensor (HO2S) high signal circuit and the HO2S low reference circuit. When measured with a 10 mega ohm digital voltmeter, this may display as low as 350 mV. The oxygen sensor signal varies from about 800 mV when the exhaust is rich, to about 50 mV when the exhaust is lean.
If the HO2S 1 voltage remains excessively high for an extended period of time, DTC P0132 will set.
Conditions for Running the DTC
| • | DTCs P0101, P0102, P0103, P0107, P0108, P0112, P0113, P0117, P0118, P0121, P0122, P0123, P0125, P0128, P0201, P0202, P0203, P0204, P0205, P0206, P0410, P0440, P0442, P0443, P0446, P0449, or P1441 are not set. |
| • | The system voltage is more than 9 volts. |
| • | The Closed Loop commanded air-to-fuel ratio is between 12 and 16.5. |
| • | The throttle angle is between 3-35 percent . |
Conditions for Setting the DTC
| • | The HO2S 1 signal voltage remains above 975 mV during normal Closed Loop operation. |
| OR |
| • | The HO2S 1 signal voltage remains above 200 mV during Deceleration Fuel Mode operation |
| • | Either of the above conditions is present for up to 50 seconds. |
Action Taken When the DTC Sets
| • | The control module illuminates the malfunction indicator lamp (MIL) on the second consecutive ignition cycle that the diagnostic runs and fails. |
| • | The control module records the operating conditions at the time the diagnostic fails. The first time the diagnostic fails, the control module stores this information in the Failure Records. If the diagnostic reports a failure on the second consecutive ignition cycle, the control module records the operating conditions at the time of the failure. The control module writes the operating conditions to the Freeze Frame and updates the Failure Records. |
Conditions for Clearing the MIL/DTC
| • | The control module turns OFF the malfunction indicator lamp (MIL) after 3 consecutive ignition cycles that the diagnostic runs and does not fail. |
| • | A current DTC, Last Test Failed, clears when the diagnostic runs and passes. |
| • | A history DTC clears after 40 consecutive warm-up cycles, if no failures are reported by this or any other emission related diagnostic. |
| • | Clear the MIL and the DTC with a scan tool. |
Diagnostic Aids
Notice: Using the J 35616-A Connector Test Adapter Kit will prevent damage to the harness connector terminals.
Check the following items:
| • | The fuel pressure--The system will go rich if pressure is too high. The PCM can compensate for some increase. However, if the fuel pressure is too high, DTC P0132 may be set. Refer to DTC P0132 . |
| • | The fuel injectors--Refer to Fuel Injector Balance Test with Special Tool . |
| • | Inspect the EVAP canister for fuel saturation. If the canister is full of fuel, inspect the canister and the hoses. |
| • | Disconnect the MAF sensor and see if rich condition is corrected. If so, replace the MAF sensor. Refer to Mass Airflow Sensor Replacement . |
| • | Test for a leaking fuel pressure regulator diaphragm by checking the vacuum line to the regulator for the presence of fuel. |
| • | An intermittent TP sensor output will cause the system to go rich due to a false indication of the engine accelerating. |
| • | A shorted heated oxygen sensor (HO2S)--If the HO2S is internally shorted, the HO2S voltage displayed on the scan tool will be more than 1 volt. Disconnect the affected HO2S and jumper the HO2S low reference circuit to ground with the key ON , and the engine OFF. If the displayed HO2S voltage changes from more than 1000 mV to approximately 450 mV, replace the HO2S. Silicon contamination of the HO2S can also cause a high HO2S voltage to be indicated. This condition is indicated by a powdery white deposit on the portion of the HO2S that is exposed to the exhaust stream. If you notice contamination, replace the affected HO2S. Refer to Heated Oxygen Sensor 1 Replacement or Heated Oxygen Sensor 2 Replacement . |
| • | An open HO2S high signal or low reference circuit or inoperative HO2S--A poor connection or an open in the HO2S high signal or low reference circuit can cause the DTC to set during deceleration fuel mode. An HO2S which is inoperative and not allowing a full voltage swing between the rich and lean thresholds can also cause this condition. Operate the vehicle while monitoring the HO2S voltage with a scan tool. If the HO2S voltage is limited within a range of 300 mV to 600 mV, check the HO2S high signal and low reference circuit wiring and the associated terminal connections. If the wiring and the connections are OK, replace the HO2S. Refer to Heated Oxygen Sensor 1 Replacement or Heated Oxygen Sensor 2 Replacement . |
| • | If the problem is intermittent, refer to Intermittent Conditions . |
Important: Remove any debris from the connector surfaces before servicing a component. Inspect the connector gaskets when diagnosing or replacing a component. Ensure that the gaskets are installed correctly. The gaskets prevent contaminate intrusion.
Check for the following conditions:
| • | Poor terminal connections--Inspect the harness connectors for the following conditions: |
| - | Backed out terminals |
| - | Improper mating |
| - | Broken locks |
| - | Improperly formed or damaged terminals |
| - | Poor terminal to wire connections--Use a corresponding mating terminal to test for proper tension. |
| • | A damaged harness--Inspect the wiring harness for damage. If the harness inspection does not reveal a problem, observe the display on the scan tool while moving connectors and wiring harnesses related to the sensor. A change in the scan tool display may indicate the location of the fault. |
| • | PCM and engine ground connections--Inspect the PCM and engine grounds for clean and secure connections. If the DTC is determined to be intermittent, reviewing the Freeze Frame/Failure Records can be useful in determining when the DTC was last set. |
Test Description
The number below refers to step number on the diagnostic table.
Step | Action | Values | Yes | No | ||||||||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Schematic Reference: Engine Controls Schematics | ||||||||||||||||||||||||||
1 | Did you perform the Diagnostic System Check-Engine Controls? | -- | Go to Step 2 | |||||||||||||||||||||||
2 |
Is the HO2S voltage less than the value specified? | 975 mV | Go to Step 3 | Go to Step 4 | ||||||||||||||||||||||
The condition that set this DTC is not present. This DTC may have been set by one of the following conditions:
Repair any of the above or similar engine conditions as necessary. Did you find and correct the condition? | -- | Go to Step 10 | Go to Diagnostic Aids | |||||||||||||||||||||||
4 |
Is the HO2S voltage within the specified value range? | 351-551 mV | Go to Step 5 | Go to Step 6 | ||||||||||||||||||||||
5 | The HO2S is detecting a rich exhaust condition or may be contaminated. Check for one of the following conditions:
Repair any of the above or similar engine conditions as necessary. Did you find and correct the condition? | -- | Go to Step 10 | Go to Step 8 | ||||||||||||||||||||||
6 |
Does the voltage measure more than the specified value? | 20 mV | Go to Step 7 | Go to Step 9 | ||||||||||||||||||||||
7 | Repair the short to voltage in the HO2S high signal circuit . Refer to Wiring Repairs in Wiring Systems. Did you complete the repair? | -- | Go to Step 10 | -- | ||||||||||||||||||||||
8 |
Important: Before replacing a contaminated HO2S, determine and repair the cause of the contamination. Replace the HO2S. Refer to Heated Oxygen Sensor 1 Replacement . Did you complete the replacement? | -- | Go to Step 10 | -- | ||||||||||||||||||||||
9 | Replace the PCM. Refer to Powertrain Control Module Replacement . Did you complete the replacement? | -- | Go to Step 10 | -- | ||||||||||||||||||||||
10 |
Important: If a rich engine condition was repaired, inspect the engine oil for fuel contamination and replace the engine oil as necessary.
Does the DTC run and pass? | -- | Go to Step 11 | Go to Step 2 | ||||||||||||||||||||||
11 | With a scan tool, observe the stored information in Capture Info. Does the scan tool display any DTCs that you have not diagnosed? | -- | System OK | |||||||||||||||||||||||
