GM Service Manual Online
For 1990-2009 cars only

Circuit Description

The accelerator pedal position (APP) sensors are located within the throttle actuator control (TAC) module assembly. The TAC module assembly is mounted to the accelerator pedal bracket. There are 3 individual APP sensors within the TAC module. Three separate signal circuits, low reference circuits, and 5-volt reference circuits are used in order to determine the accelerator pedal position. The APP sensor signal voltages increase when the accelerator pedal is depressed.

Conditions for Running the DTC

    • DTCs P0606, P1517, or P1518 are not set.
    • The ignition switch is in the crank or the run position.

Conditions for Setting the DTC

APP sensor 2 disagrees with APP sensor 1 by more than 10.5 percent, and APP sensor 2 disagrees with APP sensor 3 by more than 10.5 percent.

Action Taken When the DTC Sets

    • The control module stores the DTC information into memory when the diagnostic runs and fails.
    • The malfunction indicator lamp (MIL) will not illuminate.
    • The control module records the operating conditions at the time the diagnostic fails. The control module stores this information in the Failure Records.
    • The driver information center, if equipped, may display a message.

Conditions for Clearing the DTC

    • A current DTC Last Test Failed clears when the diagnostic runs and passes.
    • A history DTC clears after 40 consecutive warm-up cycles, if no failures are reported by this or any other non-emission related diagnostic.
    • Clear the DTC with a scan tool.

Diagnostic Aids

Important :  Remove any debris from the connector surfaces before servicing a component. Inspect the connector gaskets when diagnosing or replacing a component. Verify that the gaskets are installed correctly. The gaskets prevent intrusion of contaminates.

When the TAC module detects a condition within the electronic throttle control (ETC) system, the powertrain control module (PCM) receives a message across serial data. More than 1 ETC system-related DTC may set. This is due to the many redundant tests run continuously on this system. Locating and repairing 1 individual condition may correct more than 1 DTC. Be aware of this condition when reviewing captured DTC info.

If the DTC is determined to be intermittent, reviewing the Failure Records can be useful in determining when the DTC was last set.

Test Description

The number below refers to the step number on the diagnostic table.

  1. When the TAC module detects a condition within the ETC system, the PCM receives a message across the serial data. More than 1 ETC system-related DTC may set. This is due to the many redundant tests run continuously on this system. Locating and repairing 1 individual condition may correct more than 1 DTC. Be aware of this when reviewing captured DTC info.

Step

Action

Values

Yes

No

Schematic Reference: Engine Controls Schematics

1

Did you perform the Diagnostic System Check-Engine Controls?

--

Go to Step 2

Go to Diagnostic System Check - Engine Controls

2

Important: If any other DTCs are set, refer to the appropriate DTC for further diagnosis.

  1. Turn ON the ignition, with the engine OFF.
  2. With a scan tool, observe the APP sensor voltage parameter for this APP.

Does the scan tool indicate the voltage within the specified values?

0.5-1.3 V

Go to Step 3

Go to Step 4

3

  1. With a scan tool, observe the APP sensor Agree/Disagree parameters.
  2. Slowly depress the accelerator pedal to wide open throttle (WOT) stopping briefly at approximately the following levels:
  3. • 25 percent
    • 50 percent
    • 75 percent
  4. Then slowly return to a closed throttle position stopping briefly at approximately the following levels:
  5. • 75 percent
    • 50 percent
    • 25 percent

Does the scan tool indicate Agree for all APP sensor Agree/Disagree parameters?

--

Go to Diagnostic Aids

Go to Step 4

4

Replace the TAC module. Refer to Accelerator Pedal Position Sensor Replacement .

Did you complete the replacement?

--

Go to Step 5

--

5

  1. Use the scan tool in order to clear the DTCs.
  2. Turn OFF the ignition for 30 seconds.
  3. Operate the vehicle within the Conditions For Running the DTC as specified in the supporting text.

Does the DTC run and pass?

--

Go to Step 6

Go to Step 2

6

With a scan tool, observe the stored information, Capture Info.

Does the scan tool display any DTCs that you have not diagnosed?

--

Go to Diagnostic Trouble Code (DTC) List

System OK