Tools Required

J 28467-81 Engine Support Fixture Kit

1. Remove the hood. Refer to Hood Replacement.
2. Remove the engine cover. Refer to Intake Manifold Sight Shield Replacement.
3. Disconnect the negative battery cable from the battery. Refer to Battery Negative Cable Disconnection and Connection .



4. Remove the battery negative cable bolt (3) from the RH rear of cylinder head. Position the battery negative cable (1) and ground junction (2) aside.
5. Remove the camshaft cover ground strap from the camshaft cover. Position the ground strap aside.
6. Remove the plastic wire harness protector from the frame rail pinch weld to provide clearance for the engine lift hook.



7. Install the J 28467-87 Right Engine Lift Bracket to the right cylinder head.



8. Remove the bolt securing the wiring harness to the left cylinder head.
9. Install the J 28467-86 Left Engine Lift Bracket to the left cylinder head.



10. Assemble a J 28467-83 Rear Crossbar Support (2) to each end of the J 28467-3 Rear Crossbar (1). Secure the assembly with the lock pin (3).



11. Position the rear crossbar assembly (1-3) over the hood hinge brackets with the support located over each hood safety catch bracket.



12. Assemble a J 28467-82 Front Crossbar Legs to each end of the J 28467-85 Front Crossbar (1).



13. Install the 0.5 in X 2.5 in  J 28467-10 Quick Release Pins (4).



14. Place the front crossbar assembly with supporting legs on the right and left frame rails. Each leg should rest in the shock absorber upper mount on the frame rail.
15. Install the right and left sidebars (3-4) over the front and rear crossbars.



16. Install the J 28467-1A assembly and hand tighten.
17. Repeat steps 12 and 13 for the remaining three corners of the support fixture assembly.



18. Install the J 28467-7A lift hook through the J 28467-6A lift hook bracket.
19. Install the ½ inch lift hook washer and the J 28467-34 lift hook wing nut onto the J 28467-7A lift hook.



20. Install the J 28467-6A assembled lift hook (1) over the J 28467-84 left sidebar (2).
21. Adjust the J 28467-6A assembled lift hook bracket (1) in order to align the hook with the J 28467-86 left engine lift hook bracket.



22. Repeat step 18 for the right lift hook (3).



23. Install each J 28467-7A lift hook (5,6) through each engine lift hook bracket. Ensure that the hooks do not damage the surrounding components.
24. Hand-tighten the lift hook wing nuts securely to remove all slack from the engine support fixture assembly.

1. Loosen and remove the J 28467-7A lift hooks (5,6)
2. Remove the J 28467-81 Engine Support Fixture Kit (1-4).



3. Remove the J 28467-86 Left Engine Lift Bracket from the left cylinder head.

Notice: Refer to Fastener Notice in the Preface section.

4. Install the bolt securing the wiring harness to the left cylinder head.

Tighten
Tighten the wiring harness bolt to 35 N·m (26 lb ft).




5. Remove the J 28467-87 Right Engine Lift Bracket from the right cylinder head.
6. Install the plastic wire harness protector to the frame rail pinch weld.
7. Install the camshaft cover ground strap to the camshaft cover.

Tighten
Tighten the camshaft cover bolt to 10 N·m (89 lb in).

8. Install the battery negative cable and ground junction to the RH rear of cylinder head.

Tighten
Tighten the negative battery cable bolt to 35 N·m (26 lb ft).

9. Connect the negative battery cable to the battery. Refer to Battery Negative Cable Disconnection and Connection .
10. Install the engine cover. Refer to Intake Manifold Sight Shield Replacement.
11. Install the hood. Refer to Hood Replacement .