GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 Cadillac 🢒 2001 🢒 Seville - RHD 🢒 DTC 🢒 DTC P0449

Circuit Description

An ignition voltage is supplied directly to the evaporative emission (EVAP) canister vent valve. The control module controls the EVAP vent valve by grounding the control circuit via an internal switch called a driver. The primary function of the driver is to supply the ground for the controlled component. The control module monitors the status of the driver. If the control module detects an incorrect voltage for the commanded state of the driver, diagnostic trouble code (DTC) P0449 sets

Conditions for Running the DTC
    • The engine speed is more than 400 RPM.
    • The system voltage is between 6.0-18.0 volts.

Conditions for Setting the DTC
    • The control module detects that the commanded state of the driver and the actual state of the control circuit do not match.
    • The above conditions are present for a minimum of 5 seconds.

Action Taken When the DTC Sets
    • The control module will illuminate the malfunction indicator lamp (MIL) during the second consecutive trip in which the diagnostic test ran and failed.
    • The control module will store conditions which were present when the DTC set as Freeze Frame/Failure Records data.

Conditions for Clearing the MIL/DTC
    • The control module will turn OFF the MIL during the third consecutive trip in which the diagnostic ran and passed.
    • The History DTC will clear after 40 consecutive warm-up cycles without a malfunction.
    • The DTC can be cleared with a scan tool.

Test Description

The numbers below refer to the step numbers on the diagnostic table.

  1. A click should be heard or felt when the valve operates. Be sure that both the ON and the OFF states are commanded. Repeat the commands as necessary.

    2.

  2. This step verifies that the control module is providing ground to the EVAP vent valve.

    3.

  3. This step tests if the EVAP vent valve control circuit is grounded.

Step

Action

Yes

No

Schematic Reference: Engine Controls Schematics

1

Did you perform the Diagnostic System Check - Engine Controls?

Go to Step 2

Go to Diagnostic System Check - Engine Controls

2

  1. Turn ON the ignition, with the engine OFF.
  2. With the scan tool, command the EVAP vent valve ON and OFF.

Do you hear or feel a click from the EVAP vent valve when the valve is commanded ON and OFF?

Go to Step 3

Go to Step 4

3
  1. Review the Freeze Frame/Failure Records data for this DTC.
  2. Turn OFF the ignition for 30 seconds.
  3. Start the engine.
  4. Operate the vehicle within the Conditions for running the DTC as specified in the supporting text or as close to the Freeze Frame/Failure Records data that you observe.

Does this DTC fail this ignition?

Go to Step 4

Go to Intermittent Conditions

4
  1. Turn OFF the ignition.
  2. Disconnect the EVAP vent valve harness from the vent valve. Refer to Evaporative Emission Canister Vent Solenoid Valve Replacement
  3. Turn ON the ignition, with the engine OFF.
  4. Probe the ignition voltage circuit of the EVAP vent valve at the EVAP vent valve harness connector with a test lamp connected to a good ground. Refer to Troubleshooting with a Test Lamp

Does the test lamp illuminate?

Go to Step 5

Go to Step 11

5

  1. Connect a test lamp between the control circuit of the EVAP vent valve and ignition voltage circuit of the EVAP vent valve at the EVAP vent valve harness connector. Refer to Troubleshooting with a Test Lamp
  2. With a scan tool, command the EVAP vent valve ON and OFF.

Does the test lamp turn ON or OFF with each command?

Go to Step 9

Go to Step 6

6

Does the test lamp remain illuminated with each command?

Go to Step 8

Go to Step 7

7

Test the control circuit of the EVAP vent solenoid for a short to voltage or an open. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 14

Go to Step 10

8

Test the control circuit of the EVAP vent valve for a short to ground. Refer to Testing for Short to Ground and Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 14

Go to Step 10

9

Inspect for poor connections at the harness connector of the EVAP vent valve. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 14

Go to Step 12

10

Inspect for poor connections at the harness connector of the control module. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 14

Go to Step 13

11

Repair the ignition voltage circuit of the EVAP vent valve for an open or a short to ground. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.

Did you complete the repair?

Go to Step 14

--

12

Replace the EVAP vent valve. Refer to Evaporative Emission Canister Vent Solenoid Valve Replacement .

Did you complete the replacement?

Go to Step 14

--

13

Replace the control module. Refer to Powertrain Control Module Replacement .

Did you complete the replacement?

Go to Step 14

--

14
  1. Use a scan tool in order to clear the DTCs.
  2. Turn OFF the ignition for 30 seconds.
  3. Operate vehicle within the Conditions for Running the DTC as specified in the supporting text.

Does the DTC run and pass?

Go to Step 15

Go to Step 2

15

With a scan tool, observe the stored information, Capture Info.

Does the scan tool display any DTCs that have not been diagnosed?

Go to Diagnostic Trouble Code (DTC) List

System OK