Multifunction Turn Signal Lever Replacement - On Vehicle LHD

Caution: This vehicle is equipped with a Supplemental Inflatable Restraint (SIR) System. Failure to follow the correct procedure could cause the following conditions:

•	Air bag deployment

•	Personal injury

•	Unnecessary SIR system repairs

In order to avoid the above conditions, observe the following guidelines:

•	Refer to SIR Component Views in order to determine if you are performing service on or near the SIR components or the SIR wiring.

•	If you are performing service on or near the SIR components or the SIR wiring, disable the SIR system. Refer to Disabling the SIR System.

1. Disable the SIR system. Refer to Disabling the SIR System in SIR.
2. Remove the steering column trim covers. Refer to Steering Column Trim Covers Replacement - On Vehicle .
3. Remove the steering column wire harness tie straps (2).



4. Disconnect the steering column control module electrical connectors (2).



5. Open the lower steering column wire harness shield (1) and remove the steering column wire harness (2).

Note the direction of the steering column wiring harness is routed in the lower steering column wiring harness shield for re-installation.




6. Disconnect the multifunction switch electrical connectors (1,2, and 3).



7. Remove the multifunction switch retaining screws.



8. Remove the multifunction switch (1).

Important: The electrical contact must rest on the turn signal cancel cam assembly.

1. Install the multifunction switch (1).




Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

2. Install the multifunction switch retaining screws .

Tighten
Tighten the multifunction switch retaining screws to 7 N·m (62 lb in).




3. Connect the multifunction switch electrical connectors (1,2, and 3).



4. Install the steering column wire harness (2) to the lower steering column wire harness shield (1).



5. Connect the steering column control module electrical connectors (2).



6. Install the steering column wire harness tie straps.
7. Install the steering column trim covers. Refer to Steering Column Trim Covers Replacement - On Vehicle .
8. Enable the SIR system. Refer to Enabling the SIR System in SIR.

Multifunction Turn Signal Lever Replacement - On Vehicle RHD

Caution: This vehicle is equipped with a Supplemental Inflatable Restraint (SIR) System. Failure to follow the correct procedure could cause the following conditions:

•	Air bag deployment

•	Personal injury

•	Unnecessary SIR system repairs

In order to avoid the above conditions, observe the following guidelines:

•	Refer to SIR Component Views in order to determine if you are performing service on or near the SIR components or the SIR wiring.

•	If you are performing service on or near the SIR components or the SIR wiring, disable the SIR system. Refer to Disabling the SIR System.

1. Disable the SIR system. Refer to Disabling the SIR System in SIR.
2. Remove the steering column. Refer to Steering Column Replacement .
3. Remove the steering column trim covers. Refer to Steering Column Trim Covers Replacement - On Vehicle .
4. Remove the steering column wire harness tie straps.
5. Disconnect the steering column control module electrical connectors



6. Open the lower steering column wire harness shield (1) and remove the steering column wire harness (2).

Note the direction of the steering column wiring harness is routed in the lower steering column wiring harness shield for re-installation.




7. Disconnect the multifunction switch electrical connectors (1, 2, 3).



8. Remove the multifunction switch retaining screws (2).
9. Remove the multifunction switch from the steering column.

1. Install the multifunction switch (1) to the steering column.

Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

2. Install the multifunction switch retaining screws (2).

Tighten
Tighten the multifunction switch retaining screws to 7 N·m (62 lb in).




3. Connect the multifunction switch electrical connectors (1, 2, 3).



4. Install the steering column wire harness (2) to the lower steering column wire harness shield (1).



5. Connect the steering column control module electrical connectors (2).
6. Install the steering column wire harness tie straps.
7. Install the steering column trim covers. Refer to Steering Column Trim Covers Replacement - On Vehicle .
8. Install the steering column. Refer to Steering Column Replacement .
9. Enable the SIR system. Refer to Enabling the SIR System in SIR.