Differential Overhaul 8.6, 9.5LD inche Axles

1. Remove the differential ring gear. Refer to Drive Pinion and Ring Gear Replacement
2. Remove the differential side bearings. Refer to Differential Side Bearings Replacement.



3. Remove and discard the differential pinion gear shaft lock bolt (2). Replace with NEW only.
4. Remove the differential pinion gear shaft (1).

Note: Mark the top and bottom differential pinion gears and thrust washers, if reusing.

5. Roll the differential pinion gears (7) and the thrust washers (6) out of the differential case 2).

Note: Mark the left and right side differential side gears and the thrust washers, if reusing.

6. Remove the differential side gears (5) and the thrust washers (4).

1. Lubricate the pinion and side gears using the proper axle lubricant. Refer to Fluid and Lubricant Recommendations.
2. Install the differential side gear thrust washers (4) to the differential side gears (5).




Note: If the same differential side gears and the thrust washers are being used, install the gears and the thrust washers to their original locations.

3. Install the differential side gears (5) and thrust washers (4) into the differential case (2).
4. Position one pinion gear (7) between the differential side gears (5).
5. Position the second pinion gear (7)  between the differential side gears (5).
6. Rotate the differential side gears (5)  until the pinion gears (7)  are directly opposite the opening in the differential case (2).
7. Rotate the pinion gears (7)  toward the differential opening.
8. Install the thrust washers (6) on the pinion gears (5).
9. Rotate the pinion gears until they are aligned with the holes in the differential case (2) for the pinion shaft (1).
10. Install the pinion shaft (1).

Caution: Refer to Fastener Caution in the Preface section.

11. Install the NEW differential pinion gear shaft locking bolt and tighten to.

•	For the 8.6 inch axle, tighten the pinion bolt to 36 N·m (27 lb ft).

•	For the 9.5 inch axle, tighten the pinion bolt to 50 N·m (37 lb ft).

12. Install the differential ring gear to the differential case. Refer to Drive Pinion and Ring Gear Replacement.
13. Install the differential side bearings. Refer to Differential Side Bearings Replacement.

Differential Overhaul 10.5 Inch Axle

1. Remove the differential side bearings. Refer to Differential Side Bearings Replacement.
2. Remove the differential ring gear. Refer to Drive Pinion and Ring Gear Replacement.



3. Separate the differential case (1).




Note: If the differential pinion gears, the differential side and the thrust washers are going to be reused, mark the components so they can be re-installed in their original location in the differential case.

4. Remove the pinion gears (2), thrust washers (1) and the differential spider (3) from the differential case (6).
5. Remove the differential side gears (4) and the thrust washers (5) from the differential case (5).

1. Apply a small amount of the proper gear lubricant to the differential side gears and the differential pinion gears. Refer to Fluid and Lubricant Recommendations.




Note: If reusing the differential side and pinion gears, install them in the original position.

2. Install the thrust washers (5) differential side gears (4) into the differential case (6).
3. Install the differential pinion gears (2), thrust washer (1) on the differential spider (3).

Note: When installing the differential spider and gears assembly, rotate the differential side gears until the

4. Position the differential thrust washers (1), pinion gears (2) and the spider (3) in the differential case (5).



5. Align the arrows on the differential case halves before



6. Position the differential side gear (3) and the thrust washer (3) on the differential pinion gears (4).
7. Install the differential case half (1).
8. Install the differential ring gear. Refer to Drive Pinion and Ring Gear Replacement.
9. Install the differential side bearings. Refer to Differential Side Bearings Replacement.