GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 Buick 🢒 2002 🢒 LeSabre 🢒 Body and Accessories 🢒 Body Control System 🢒 Inflatable Restraint Sensing and Diagnostic Module Replacement

Inflatable Restraint Sensing and Diagnostic Module Replacement AG1/AG2

CAUTION: Be careful when you handle a sensing and diagnostic module (SDM). Do not strike or jolt the SDM. Before applying power to the SDM:

   • Remove any dirt, grease, etc. from the mounting surface
   • Position the SDM horizontally on the mounting surface
   • Point the arrow on the SDM toward the front of the vehicle
   • Tighten all of the SDM fasteners and SDM bracket fasteners to the specified torque value
Failure to follow the correct procedure could cause air bag deployment, personal injury, or unnecessary SIR system repairs.

Removal Procedure

    Object Number: 291625 Size: SH
  1. Disable the SIR system. Refer to Disabling the SIR System .
  2. Move both driver and passenger seat forward and/or to the rear in order to gain access to console fasteners.
  3. Remove the console. Refer to Console Replacement in Instrument Panel, Gauges and Console.
  4. When the console is removed the carpet will be pre-slit in order to provide access to the inflatable restraint sensing and diagnostic module (SDM).

    5. Object Number: 466123 Size: SH
  5. Remove the Connector Position Assurance (CPA) (1) from the inflatable restraint sensing and diagnostic module (SDM) wiring harness connector (2).
  6. Push down flex lock button (3) and then move sliding connector locking cover (4) to the open position.

    7. Object Number: 464945 Size: SH
  7. Remove push-on clip (1) securing SDM wiring harness to console stud.
  8. Disconnect the SDM wiring harness connector (3) from the SDM (2).

    9. Object Number: 464950 Size: SH
  9. Remove the SDM mounting fasteners (1).
  10. Remove the SDM (2) from the console floor (3).

Installation Procedure

    Object Number: 464950 Size: SH
  1. Install the SDM (2) to console floor (3).

    2. Notice: Refer to Fastener Notice in the Preface section.

  2. Install the SDM mounting fasteners (1).

    3. Tighten
    Tighten the fasteners to 9 N·m (80 lb in).


    Object Number: 464945 Size: SH
  3. Connect the SDM wiring harness connector (3) to the SDM (2).
  4. Install the push-on clip (1) securing the SDM wiring harness to the console stud.

    5. Object Number: 466123 Size: SH
  5. Push down flex lock button (3) and then move sliding connector locking cover (4) to the close position.
  6. Install the Connector Position Assurance (CPA) (1) to the inflatable restraint sensing and diagnostic module (SDM) wiring harness connector (2).

    7. Object Number: 291625 Size: SH
  7. Install the carpet pre-slit to the close position covering the inflatable restraint sensing and diagnostic module (SDM).
  8. Install the console. Refer to Console Replacement in Instrument Panel, Gauges and Console.
  9. Position the driver and passenger seats to the original positions.
  10. Enable the SIR system. Refer to Enabling the SIR System .

    11. Important: The AIR BAG indicator may remain ON after the SDM has been replaced. DTC B1001 may set requiring the SDM part number to be set in multiple modules. If the indicator remains ON after enabling the SIR system, perform the diagnostic system check and follow the steps thoroughly to ensure that the SDM is set properly.

  11. Program the SDM. Refer to Body Control Module (BCM) Programming/RPO Configuration in Body Control System.

Inflatable Restraint Sensing and Diagnostic Module Replacement AM6

CAUTION: Be careful when you handle a sensing and diagnostic module (SDM). Do not strike or jolt the SDM. Before applying power to the SDM:

   • Remove any dirt, grease, etc. from the mounting surface
   • Position the SDM horizontally on the mounting surface
   • Point the arrow on the SDM toward the front of the vehicle
   • Tighten all of the SDM fasteners and SDM bracket fasteners to the specified torque value
Failure to follow the correct procedure could cause air bag deployment, personal injury, or unnecessary SIR system repairs.

Removal Procedure

    Object Number: 381863 Size: SH
  1. Disable the SIR system. Refer to Disabling the SIR System .
  2. Remove the front split bench seat. Refer to Split Bench Seat Replacement in Seats.
  3. Remove the rear carpet from vehicle. Refer to Rear Floor Panel Carpet Replacement in Interior Trim.

    4. Object Number: 466123 Size: SH
  4. Remove the Connector Position Assurance (CPA) (1) from the inflatable restraint sensing and diagnostic module (SDM) wiring harness connector (2).
  5. Push down flex lock button (3) and then move sliding connector locking cover (4) to the open position.

    6. Object Number: 464945 Size: SH
  6. Remove the push-on clip (1) securing the SDM wiring harness to the console stud.
  7. Disconnect the SDM wiring harness connector (3) from the SDM (2).

    8. Object Number: 464950 Size: SH
  8. Remove the SDM mounting fasteners (1).
  9. Remove the SDM (2) from the console floor (3).

Installation Procedure

    Object Number: 464950 Size: SH
  1. Install the SDM (2) to console floor (3).

    2. Notice: Refer to Fastener Notice in the Preface section.

  2. Install the SDM mounting fasteners (1).

    3. Tighten
    Tighten the fasteners to 9 N·m (80 lb in).


    Object Number: 464945 Size: SH
  3. Connect the SDM wiring harness connector (3) to the SDM (2).
  4. Install the push-on clip (1) securing the SDM wiring harness to the console stud.

    5. Object Number: 466123 Size: SH
  5. Push down flex lock button (3) and then move sliding connector locking cover (4) to the close position.
  6. Install the Connector Position Assurance (CPA) (1) to the inflatable restraint sensing and diagnostic module (SDM) wiring harness connector (2).

    7. Object Number: 381863 Size: SH
  7. Install the rear carpet into vehicle. Refer to Rear Floor Panel Carpet Replacement in Interior Trim.
  8. Install the front split bench seat. Refer to Split Bench Seat Replacement in Seats.
  9. Enable the SIR system. Refer to Enabling the SIR System .

    10. Important: The AIR BAG indicator may remain ON after the SDM has been replaced. DTC B1001 may set requiring the SDM part number to be set in multiple modules. If the indicator remains ON after enabling the SIR system, perform the diagnostic system check and follow the steps thoroughly to ensure that the SDM is set properly.

  10. Program the SDM. Refer to Body Control Module (BCM) Programming/RPO Configuration in Body Control System.