Circuit Description
The PCM monitors the EGR valve pintle position input to ensure that the valve responds properly to commands from the PCM and to detect a fault if the pintle position sensor circuit is open or shorted. If the PCM detects an excessively low EGR Feedback signal voltage, DTC P0405 will set.
Conditions for Running the DTC
| • | No TP, MAF, IAT, or ECT, sensor HO2S DTCs are set. |
| • | Engine coolant temperature is greater than 75°C (167°F). |
| • | Engine run time met. The time ranges from 20 seconds to 6 minutes depending upon engine coolant temperature at startup. |
| • | TP angle is greater than 2%. |
| • | Vehicle speed is greater than 2 mph (3.2 km/h) |
| • | System voltage is greater than 10 volts. |
Conditions for Setting the DTC
| • | EGR Feedback is less than 0.14 volt at any time. |
| • | The condition is present for longer than 25 seconds. |
Action Taken When the DTC Sets
| • | The PCM will illuminate the malfunction indicator lamp (MIL) during the second consecuitive trip in which the diagnostic has been run and failed. |
| • | If equipped with traction control, the PCM will command the EBTCM via the serial data circuit to turn OFF traction control, and the EBTCM will illuminate the TRACTION OFF lamp. |
| • | The PCM will store conditions which were present when the DTC set as Freeze Frame and Failure Records data. |
Conditions for Clearing the MIL/DTC
| • | The PCM will turn OFF the MIL during the third consecutive trip in which the diagnostic has been run and passed. |
| • | The History DTC will clear after 40 consecutive warm-up cycles have occurred without a malfunction. |
| • | The DTC can be cleared by using the scan tool. |
Diagnostic Aids
| • | Poor connection at PCM or EGR Valve. |
| Inspect the harness connectors for backed out terminals, improper mating, borken locks, improperly formed or damaged terminals, and poor terminal to wire connection. |
| • | Damaged harness. |
| Inspec the wiring harness for damage. If the harness appears to be OK, connect J 39200 DMM and check circuit continuity while moving connectors and wiring harnesses related to the EGR valve. A change in the DMM display will indicate the location of the malfunciton. |
Refer to Intermittents and Poor Connections Diagnosis Connector Repairs and Wiring Repairs .
Test Description
Number(s) below refer to the step number(s) on the Diagnostic Table:
-
Verifies that the malfunction is present.
-
If DTC P0405 will only set under certain conditions, the malfunction may be intermittent; refer to Diagnostic Aids. If an intermittent wiring problem is not present, check for a poor connection at the PCM or the EGR valve.
-
This vehicle is equipped with a PCM which utilizes an Electrically Erasable Programmable Read Only Memory (EEPROM). When the PCM is being replaced, the new PCM must be programmed.
Step | Action | Value(s) | Yes | No | ||||||
|---|---|---|---|---|---|---|---|---|---|---|
1 | Was the Powertrain on-Board Diagnostic (OBD) System Check performed? | -- | ||||||||
Does Desired EGR Position remain close to Actual EGR Position at all commanded positions? | -- | |||||||||
Does the scan tool indicate DTC P0405 failed this ignition? | -- | Go to Diagnostic Aids | ||||||||
4 |
Is the voltage at the specified value? | 5.0V | ||||||||
5 | Probe the EGR valve pintle position circuit at the EGR valve harness connector with a J 35616-200 test light connected to battery positive voltage. Is the a J 35616-200 test light on? | -- | ||||||||
6 |
Is the Actual EGR Position at the specified value? | 100% | ||||||||
7 |
Was a problem found? | -- | ||||||||
8 |
Is the a J 35616-200 test light on? | -- | ||||||||
9 | Probe the 5 Volt Reference A circuit with a J 35616-200 test light to battery positive voltage. Is the J 35616-200 test light on? | -- | ||||||||
10 |
Is the J 35616-200 test light on? | -- | ||||||||
11 |
Was a problem found? | -- | ||||||||
12 | Locate and correct the short to ground in the EGR valve pintle position circuit. Refer to Wiring Repairs . Is the action complete? | -- | -- | |||||||
13 |
Was a problem found? | -- | ||||||||
14 | Replace the EGR valve. Refer to Exhaust Gas Recirculation Valve Replacement . Notice: If the EGR valve shows signs of excessive heat, inspect the exhaust
system for blockage--possibly a plugged converter--using the procedure
found on the Restricted Exhaust System Check. If the exhaust system is restricted,
repair the cause. Inspect for an open injector caused by one or more of the
following conditions:
Is the action complete? | -- | -- | |||||||
15 |
Was a problem found? | -- | ||||||||
16 | Locate and repair short to ground in the 5 Volt Reference A circuit. Refer to Wiring Repairs . Is the action complete? | -- | -- | |||||||
17 |
Was a problem found? | -- | ||||||||
|
Important: : The replacement PCM must be programmed. Refer to Powertrain Control Module Replacement/Programming . Replace the PCM. Is the action complete? | -- | -- | ||||||||
19 |
Does the scan tool indicate DTC P0405 failed this ignition? | -- | System OK |
