Low and High Beams Headlamps Inoperative Domestic
Step | Action | Value(s) | Yes | No |
|---|---|---|---|---|
1 | Was the headlamp diagnostic system check performed? | -- | Go to Step 2 | Go to Headlight System Check |
2 | Inspect the HEADLAMP circuit breaker. Is the circuit breaker open? | -- | Go to Step 3 | Go to Step 4 |
3 | Repair a short to ground in CKT 2340. Is the repair complete? | -- | Go to Headlight System Check | -- |
4 |
Did the test lamp light? | -- | Go to Step 8 | Go to Step 5 |
5 | Use a test lamp in order to backprobe between the headlamp dimmer switch harness connector terminal L and ground. Did the test lamp light? | -- | Go to Step 7 | Go to Step 6 |
6 | Use a test lamp in order to backprobe between the headlamp and instrument panel dimmer switch harness connector terminal N and ground. Did the test lamp light? | -- | Go to Step 9 | Go to Step 10 |
7 | Repair the faulty connection and/or open in CKT 10 between C201 terminal E13 and the headlamp dimmer switch connector terminal L. Is the repair complete? | -- | Go to Headlight System Check | -- |
8 |
Did the test lamp light? | -- | Go to Step 11 | Go to Step 9 |
9 | Replace the headlamp dimmer switch. Refer to Multifunction, Turn Signal, and Hazard Switch Replacement - On Vehicle in Instrument Panel, Gauges, and Console. Is the repair complete? | -- | Go to Headlight System Check | -- |
10 | Repair the faulty connection or open in CKT 2340. Is the repair complete? | -- | Go to Headlight System Check | -- |
11 |
Did the test lamp light? | -- | Go to Step 12 | Go to Step 9 |
12 | If the test lamp was lit in either Step 8 or Step 11, refer to Headlamps Inoperative - Low Beams or Headlamps Inoperative - High Beams . Was the test lamp lit in Step 8 or Step 11? | -- | Go to Headlamps Inoperative - Low Beams or Headlamps Inoperative - High Beams | -- |
Low and High Beams Headlamps Inoperative Export
Step | Action | Value(s) | Yes | No |
|---|---|---|---|---|
1 | Was the headlamp diagnostic system check performed? | -- | Go to Step 2 | Go to Headlight System Check |
2 | Inspect the HEADLAMP circuit breaker. Is the circuit breaker open? | -- | Go to Step 3 | Go to Step 4 |
3 | Repair a short to ground in CKT 2340. Is the repair complete? | -- | Go to Headlight System Check | -- |
4 |
Did the test lamp light? | -- | Go to Step 8 | Go to Step 5 |
5 | Use a test lamp in order to backprobe between the headlamp dimmer switch harness connector terminal L and ground. Did the test lamp light? | -- | Go to Step 7 | Go to Step 6 |
6 | Use a test lamp in order to backprobe between the headlamp and instrument panel dimmer switch harness connector terminal N and ground. Did the test lamp light? | -- | Go to Step 9 | Go to Step 10 |
7 | Repair the faulty connection and/or open in CKT 10 between C201 terminal E13 and the headlamp dimmer switch connector terminal L. Is the repair complete? | -- | Go to Headlight System Check | -- |
8 |
Did the test lamp light? | -- | Go to Step 11 | Go to Step 9 |
9 | Replace the headlamp dimmer switch. Refer to Multifunction, Turn Signal, and Hazard Switch Replacement - On Vehicle in Instrument Panel, Gauges, and Console. Is the repair complete? | -- | Go to Headlight System Check | -- |
10 | Repair the faulty connection or open in CKT 2340. Is the repair complete? | -- | Go to Headlight System Check | -- |
11 |
Did the test lamp light? | -- | Go to Step 12 | Go to Step 9 |
12 | If the test lamp was lit in either Step 8 or Step 11, refer to Headlamps Inoperative - Low Beams or Headlamps Inoperative - High Beams . Was the test lamp lit in Step 8 or Step 11? | -- | Go to Headlamps Inoperative - Low Beams or Headlamps Inoperative - High Beams | -- |
