GM Service Manual Online
For 1990-2009 cars only

Removal Procedure

Caution: For safety reasons, the Brake Pressure Modulator Valve (BPMV) must not be repaired; the complete unit must be replaced. With the exception of the EBCM/EBTCM, no screws may be loosened. If screws are loosened, it will not be possible to get the brake circuits leak-tight and personal injury may result.


    Object Number: 230405  Size: SH
  1. Turn the ignition switch to the OFF position.
  2. Pull out lock tab (1) from EBCM harness connector.
  3. Disconnect the EBCM harness connector.

  4. Object Number: 230408  Size: SH

    Important: Note the locations of the brake pipes in order to aid in installation.

  5. Disconnect the wheel cylinder brake pipes (1) from the BPMV (2).

  6. Object Number: 230409  Size: SH
  7. Disconnect the master cylinder brake pipes (1) from the BPMV (2).

  8. Object Number: 230410  Size: SH
  9. Remove the two nuts (1) that connect the BPMV to the BPMV bracket.
  10. Notice: When removing the brake pressure modulator valve, protect the vehicle exterior from possible brake fluid spillage. Brake fluid can cause damage to painted surfaces.

  11. Remove the BPMV (2) and EBCM as an assembly from the vehicle.
  12. Remove EBCM if replacing the BPMV only. Refer to Electronic Brake Control Module Replacement .

Installation Procedure


    Object Number: 230410  Size: SH
  1. Install EBCM if replacing the BPMV only. Refer to Electronic Brake Control Module Replacement .
  2. Install BPMV (2) and EBCM as an assembly into the BPMV bracket. Align the flats of the studs on the BPMV with the BPMV bracket.
  3. Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

  4. Install the two BPMV to BPMV bracket nuts (1).
  5. Tighten
    Tighten the two BPMV to BPMV bracket nuts to 12 N·m (8 lb ft).


    Object Number: 230409  Size: SH

    Important: 

       • If a new BPMV is being installed, remove the shipping plugs from the valve openings in the compartment during the next step.
       • Use the locations noted during removal.

    Caution: Make sure brake pipes are correctly connected to brake pressure modulator valve. If brake pipes are switched by mistake, wheel lockup will occur and personal injury may result. The only two ways this condition can be detected are by using a Scan Tool or by doing an Antilock stop.

  6. Install the master cylinder brake pipes (1) on the BPMV (2).

  7. Object Number: 230408  Size: SH
  8. Install the wheel cylinder brake pipes (1) on the BPMV (2).
  9. Tighten
    Tighten all of the brake pipe fittings to 15 N·m (11 lb ft).


    Object Number: 230405  Size: SH
  10. Connect the EBCM harness connector. Push in lock tab (1).
  11. Fill and bleed the brake hydraulic system. Refer to Hydraulic Brake System Bleeding in Hydraulic Brakes.
  12. Turn the ignition switch to the ON position, engine off.
  13. Perform the Diagnostic System Check - ABS .