GM Service Manual Online
For 1990-2009 cars only

Cuts Out, Misses Symptom

Step

Action

Value(s)

Yes

No

Definition: Steady pulsation or jerking that follows engine speed; usually more pronounced as engine load increases.

1

Was the Powertrain On-Board Diagnostic(OBD) System Check performed?

--

Go to Step 2

Go to the Powertrain On Board Diagnostic (OBD) System Check

2

  1. Perform a bulletin search.
  2. If a bulletin that addresses the symptom is found, correct the condition as instructed in the bulletin.

Was a bulletin found that addresses the symptom?

--

Go to Step 13

Go to Step 3

3

Was visual/physical check performed?

--

Go to Step 4

Go to Visual/Physical Checks

4

  1. Check PCM grounds for being clean, tight and proper routing. Refer to Engine Controls Schematics .
  2. If a problem is found, repair as necessary.

Was a problem found?

--

Go to Step 25

Go to Step 5

5

Observe Long Term Fuel Trim on the scan tool.

Is Long Term Fuel Trim significantly in the negative range (Rich condition)?

--

Go to Step 6

Go to Step 7

6

  1. Check items that can cause the engine to run rich. Refer to DTC P0172 Fuel Trim System Rich .
  2. If a problem is found, repair as necessary.

Was a problem found?

--

Go to Step 25

Go to Step 9

7

Is Long Term Fuel Trim significantly in the positive range (Lean condition)?

--

Go to Step 8

Go to Step 9

8

  1. Check items that can cause the engine to run lean. Refer to DTC P0171 Fuel Trim System Lean
  2. .

  3. If a problem is found, repair as necessary.

Was a problem found?

--

Go to Step 25

Go to Step 9

9

  1. Check for incorrect idle speed. Ensure that the following conditions are present:
  2. • Engine fully warm.
    • Accessories off.
  3. Using a scan tool, monitor IAC position.

Is IAC position within the specified values? (Value is displayed in counts).

5-50

Go to Step 11

Go to Step 10

10

  1. Visually/physically inspect for the following conditions:
  2. • Throttle body tampering (Adjustment screw plug removed).
    • Restricted air intake system. Check for a possible collapsed air intake duct, restricted air filter element, or foreign objects blocking the air intake system. Refer to Air Induction System .
    • Throttle body. Check for objects blocking the IAC passage or throttle bore, excessive deposits in the IAC passage and on the IAC pintle, and excessive deposits in the throttle bore and on the throttle plate.
    • Large vacuum leak. Check for a condition that causes a large vacuum leak, such as a incorrectly installed or faulty crankcase ventilation valve or brake booster hose disconnected.
  3. If a problem is found, repair as necessary.

Was a problem found?

--

Go to Step 25

Go to Step 8

11

Check the injector connections. If any of the injectors are connected to an incorrect cylinder, correct as necessary.

Was a problem found?

--

Go to Step 25

Go to Step 12

12

  1. Perform the Fuel Injector Solenoid Coil Test / Fuel Injector Balance Test in Fuel Metering System.
  2. If a problem is found, repair as necessary.

Was a problem found?

--

Go to Step 25

Go to Step 13

13

  1. Check for fuel in pressure regulator vacuum hose.
  2. If fuel is present, replace the fuel pressure regulator assembly. Refer to Fuel Pressure Regulator Replacement .
  3. If a problem is found, repair as necessary.

Was a problem found?

--

Go to Step 25

Go to Step 14

14

  1. Check for proper ignition coil output voltage with spark tester J 26792 :
  2.  - Clip the spark tester to engine ground.
     - Connect one end of a spark plug wire to the spark tester; connect the other end of the spark plug wire to the coil being tested.
     - Connect one end of another spark plug wire to the other coil tower; connect the other end of the spark plug wire to ground.
     - Crank the engine while observing the spark tester; a crisp blue spark should be observed.
     - Repeat the above steps for each coil.
  3. If adequate spark is not present at all coils, repair as necessary.

Was a problem found?

--

Go to Step 25

Go to Step 15

15

  1. Remove spark plugs, check for wet plugs, cracks, wear, improper gap, burned electrodes, or heavy deposits.
  1. If a problem is found, repair as necessary.

Was a problem found?

--

Go to Step 25

Go to Step 16

16

  1. Check for loose ignition control module ground.
  2. If a problem is found, repair as necessary.

Was a problem found?

--

Go to Step 25

Go to Step 17

17

  1. Check ignition coils for cracks or carbon tracking.
  2. If a problem is found, repair as necessary.

Was a problem found?

--

Go to Step 25

Go to Step 18

18

Using a Scan Tool, monitor TP angle with the engine idling.

Is TP angle at the specified value and steady?

0%

Go to Step 19

For further diagnosis, refer to DTC P0123 Throttle Position (TP) Sensor Circuit High Voltage .

19

  1. Check crankcase ventilation valve for proper operation. Refer to Crankcase Ventilation System .
  2. If a problem is found, repair as necessary.

Was a problem found?

--

Go to Step 25

Go to Step 20

20

  1. Check Transaxle Range switch circuit; use a scan tool and be sure the scan tool indicates that the vehicle is in drive with gear selector in drive or overdrive.
  2. If a problem is found, diagnose and repair Transaxle Range switch as necessary. For diagnosis refer to DTC P0705 Trans Range Switch Circuit . For repair, refer to Transaxle Range Switch .

Was a problem found?

--

Go to Step 25

Go to Step 21

21

  1. Check the following items (Refer to Electronic Ignition (EI) System .):
  2. • Damaged or bent harmonic balancer interrupter rings.
    • Damaged crankshaft position sensor.
  3. If a problem is found, repair as necessary.

Was a problem found?

--

Go to Step 25

Go to Step 22

22

  1. Check the following engine mechanical items. Refer to Engine Mechanical for diagnosis procedures:
  2. • Check compression.
    • Sticking or leaking valves.
    • Worn camshaft lobe(s).
    • Valve timing.
    • Bent push rods.
    • Worn rocker arms.
    • Broken valve springs.
  3. If a problem is found, repair as necessary.

Was a problem found?

--

Go to Step 25

Go to Step 23

23

  1. Check for faulty motor mounts. Refer to Engine Mechanical for inspection of mounts.
  2. If a problem is found, repair as necessary.

Was a problem found?

--

Go to Step 25

Go to Step 24

24

  1. Review all diagnostic procedures within this table.
  2. If all procedures have been completed and no malfunctions have been found, review/inspect the following:
  3. • Visual/physical inspection.
    • Scan Tool data.
    • Freeze Frame data/Failure Records Data.
    • All electrical connections within a suspected circuit and/or system.
  4. If a problem is found, repair as necessary.

Was a problem found?

--

Go to Step 25

Refer to Technical Service Bulletins

25

Operate the vehicle to duplicate conditions present when the original symptom was noted.

Is symptom still present?

--

Go to Step 3

System OK