Engine Coolant Inlet Pipe Replacement 2.4L

Notice: When adding coolant, it is important that you use GM Goodwrench DEX-COOL™ coolant. If coolant other than DEX-COOL™ is added to the system, the engine coolant will require change sooner: at 50 000 km (30,000 miles) or 24 months.

1. Drain and recover the coolant. Refer to Cooling System Draining and Filling .
2. Remove the exhaust manifold heat shield.



3. Remove the coolant inlet pipe bolts through the exhaust manifold.
4. Raise the vehicle. Refer to Lifting and Jacking the Vehicle in General Information.
5. Remove the tire and wheel assembly. Refer to Tire and Wheel Removal and Installation
6. Remove the splash shield. Refer to Wheelhouse Splash Shield Replacement .
7. Remove the bolts from the transaxle-to-engine block brace. Remove the brace.
8. Remove the radiator hose from the coolant inlet pipe to oil pan bolt.
9. Remove the cover to the coolant inlet pipe bolt.
10. Remove the coolant inlet pipe and the seal.

1. Install the seal and the inlet pipe.

Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

2. Connect the cover to the inlet pipe bolt.

Tighten
Tighten the bolt to 14 N·m (124 lb in).

3. Install the inlet pipe to the oil pan bolt.

Tighten
Tighten the bolt to 26 N·m (19 lb ft).

4. Connect the radiator hose to the inlet pipe.
5. Install the transaxle-to-engine block brace with a bolt.
6. Install the splash shield. Refer to Wheelhouse Splash Shield Replacement .
7. Install the tire and wheel assembly.
8. Lower the vehicle.
9. Install the coolant inlet pipe bolt through the exhaust manifold.

Tighten
Tighten the bolt to 14 N·m (124 lb in).

10. Install the exhaust manifold heat shield.
11. Fill the cooling system. Refer to Cooling System Draining and Filling .

Engine Coolant Inlet Pipe Replacement 3.1L

Notice: When adding coolant, it is important that you use GM Goodwrench DEX-COOL™ coolant. If coolant other than DEX-COOL™ is added to the system, the engine coolant will require change sooner: at 50 000 km (30,000 miles) or 24 months.

1. Drain and recover the coolant.

Refer to Cooling System Draining and Filling .

2. Remove the exhaust manifold heat shield.



3. Remove the coolant inlet pipe bolt through the exhaust manifold.
4. Raise the vehicle. Refer to Lifting and Jacking the Vehicle in General Information.
5. Remove the radiator hose from the coolant inlet pipe to oil pan bolt. Refer to Radiator Hose Replacement .
6. Remove the cover to the coolant inlet pipe bolt.
7. Remove the coolant inlet pipe and seal.

1. Install the seal and inlet pipe.
2. Connect the cover to the inlet pipe bolt.

Tighten
Tighten the bolt to 14 N·m (124 lb in).

Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

3. Install the inlet pipe to the oil pan bolt.

Tighten
Tighten the bolt to 26 N·m (19 lb ft).

4. Connect the radiator hose to the inlet pipe.
5. Lower the vehicle.
6. Install the coolant inlet pipe bolt through the exhaust manifold.

Tighten
Tighten the bolt to 14 N·m (124 lb in).

7. Install the exhaust manifold heat shield.
8. Fill the cooling system.

Refer to Cooling System Draining and Filling .