GM Service Manual Online
For 1990-2009 cars only

Circuit Description

The manifold absolute pressure (MAP) sensor responds to pressure changes in the intake manifold. The pressure changes occur based on the engine load. The MAP sensor has a 5-volt reference circuit, a low reference circuit, and a signal circuit. The powertrain control module (PCM) supplies 5 volts to the MAP sensor on the 5-volt reference circuit. The PCM also provides a ground on the low reference circuit. The MAP sensor provides a signal to the PCM on the signal circuit which is relative to the pressure changes in the manifold. The PCM should detect a low signal voltage at a low MAP, such as during an idle or a deceleration. The PCM should detect a high signal voltage at a high MAP, such as the ignition is ON, with the engine OFF, or at a wide open throttle (WOT). Certain vehicle models will also use the MAP sensor in order to determine the barometric pressure (BARO). This occurs when the ignition switch is turned ON, with the engine OFF. The BARO reading may also be updated whenever the engine is operated at WOT. The PCM monitors the MAP sensor signal for voltage outside of the normal range. The PCM calculates a predicted value for the MAP sensor based on throttle position and engine speed. The PCM then compares the predicted value to the actual MAP sensor signal. DTC P0105 will set if the MAP sensor signal is not within the predicted range.

Conditions for Running the DTC

    • DTC P0107, P0108, P0116, P0117, P0118, P0122, P0123, P0125, P0128, P0130, P0131, P0132, P0171, P0172, P0201, P0202, P0203, P0204, P0205, P0206, P0300, P0301, P0302, P0303, P0304, P0305, P0306, P0335, P0336, P0340, P0341, P0351, P0352, P0353, P0354, P0355, P0356, P0440, P0442, P0446, P0452, P0453, P0502, P0506, P0507, P0740, P0741, P0742, P1120, P1220, P1221, P1271, P1275, P1280, P1441, P1512, P1514, P1515, P1516, P1635, P1639, P1680, P1681, or P1860 are not set.
    • The engine run time is more than 40 seconds.
    • The change in engine speed is stable to within 50 RPM.
    • The engine speed is between 600--637 RPM.
    • The torque converter clutch (TCC) is stable to within 2.5 percent.
    • All conditions stable for 1.5 seconds.

Conditions for Setting the DTC

The actual MAP sensor signal is not within the predicted range for 14 seconds.

Action Taken When the DTC Sets

    • The control module illuminates the malfunction indicator lamp (MIL) on the second consecutive ignition cycle that the diagnostic runs and fails.
    • The control module records the operating conditions at the time the diagnostic fails. The first time the diagnostic fails, the control module stores this information in the Failure Records. If the diagnostic reports a failure on the second consecutive ignition cycle, the control module records the operating conditions at the time of the failure. The control module writes the operating conditions to the Freeze Frame and updates the Failure Records.

Conditions for Clearing the MIL/DTC

    • The control module turns OFF the malfunction indicator lamp (MIL) after 3 consecutive ignition cycles that the diagnostic runs and does not fail.
    • A current DTC, Last Test Failed, clears when the diagnostic runs and passes.
    • A history DTC clears after 40 consecutive warm-up cycles, if no failures are reported by this or any other emission related diagnostic.
    • Clear the MIL and the DTC with a scan tool.

Diagnostic Aids

    • Inspect for the following conditions:
       - Restrictions in the MAP sensor vacuum source
       - MAP sensor seal is missing or damaged
       - Vacuum hoses disconnected, damaged, or incorrectly routed
       - Intake manifold vacuum leaks
       - Vacuum leaks at the throttle body
    • This DTC may set due to any condition that may cause an unreasonably high or low MAP value including the following engine conditions:
       - Incorrect cam timing
       - Restricted exhaust
       - Worn piston rings
       - Low fuel pressure
    • If an intermittent condition exists, refer to Intermittent Conditions .

Test Description

The numbers below refer to the step numbers on the diagnostic table.

  1. This step tests the MAP sensor's ability to correctly indicate barometric pressure. The value shown for the MAP sensor varies with altitude. 103 kPa is the approximate barometric pressure (BARO) displayed at or near sea level.

  2. This step tests the MAP sensor's ability to respond to an increase in engine vacuum.

  3. This step tests for a proper MAP sensor pressure with an applied vacuum.

Step

Action

Values

Yes

No

Schematic Reference: Engine Controls Schematics

Connector End View Reference: Engine Controls Connector End Views

1

Did you perform the Diagnostic System Check-Engine Controls?

--

Go to Step 2

Go to Diagnostic System Check - Engine Controls

2

Inspect for the following conditions:

   • 

MAP sensor seal missing or damaged

   • 

Restrictions in the MAP sensor vacuum source

   • 

Vacuum hoses disconnected, damaged, or incorrectly routed

   • 

Vacuum leaks between the intake manifold and the engine

   • 

Vacuum leaks at the throttle body

Did you find and correct the condition?

--

Go to Step 22

Go to Step 3

3

  1. Install a scan tool.
  2. Turn ON the ignition, with the engine OFF.
  3. Monitor the scan tool and record the MAP sensor pressure.
  4. Compare the MAP sensor pressure to that of a known good vehicle.

Is the pressure difference between the vehicles less than the specified value.

3 kPa

Go to Step 4

Go to Step 8

4

  1. Observe the MAP sensor pressure on the scan tool.
  2. Start the engine.

Does the MAP sensor value change?

--

Go to Step  5

Go to Step 8

5

  1. Turn OFF the ignition.
  2. Remove the MAP sensor from the vacuum source. Refer to Manifold Absolute Pressure Sensor Replacement .
  3. Leave the electrical harness connected.
  4. Connect a hand vacuum pump to the MAP sensor.
  5. Turn ON the ignition, with the engine OFF.
  6. Observe the MAP sensor pressure as you SLOWLY apply vacuum 1 in Hg at a time. Each inch of vacuum should result in a 3-4 kPa drop in the MAP sensor pressure.
  7. Increase the vacuum to 20 in Hg.

Does the scan tool indicate that the MAP sensor pressure decreases smoothly through the test?

--

Go to Step  6

Go to Step 18

6

Observe the MAP sensor pressure with 20 in HG of vacuum applied to the MAP sensor.

Does the scan tool indicate that the MAP sensor pressure is less than the specified value?

34 kPa

Go to Step 7

Go to Step 8

7

Disconnect the MAP sensor from the hand vacuum pump.

Does the MAP sensor pressure return to the original value that was observed in step 3?

--

Go to Diagnostic Aids

Go to Step 18

8

  1. Turn OFF the ignition.
  2. Disconnect the MAP sensor electrical connector.
  3. Turn ON the ignition, with the engine OFF.

Does the scan tool indicate that the MAP sensor voltage is more than the specified value?

0.3 V

Go to Step 17

Go to Step 9

9

Probe the 5-volt reference circuit of the MAP sensor with a test lamp that is connected to a good ground.

Does the test lamp illuminate?

--

Go to Step 10

Go to Step 16

10

Connect a 3-amp fused jumper wire between the 5-volt reference circuit of the MAP sensor and the signal circuit of the MAP sensor.

Does the scan tool indicate that the MAP sensor voltage is near the specified value?

5 V

Go to Step 11

Go to Step 15

11

  1. Remove the jumper wire.
  2. Measure the voltage from the 5-volt reference circuit of the MAP sensor to a good ground.

Does the voltage measure more than the specified value?

5.2 V

Go to Step 13

Go to Step 12

12

Probe the low reference circuit of the MAP sensor with a test lamp that is connected to battery positive voltage.

Does the test lamp illuminate?

--

Go to Step 18

Go to Step 14

13

Test the 5-volt reference circuit of the MAP sensor for a short to voltage. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

--

Go to Step 22

Go to Step 19

14

Test the low reference circuit of the MAP sensor for high resistance or an open. Refer to Testing for Continuity and Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

--

Go to Step 22

Go to Step 19

15

Test the signal circuit of the MAP sensor for high resistance. Refer to Testing for Continuity and Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

--

Go to Step 22

Go to Step 19

16

Test the 5-volt reference circuit of the MAP sensor for high resistance. Refer to Testing for Continuity and Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

--

Go to Step 22

Go to Step 19

17

Test the signal circuit of the MAP sensor for a short to voltage. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

--

Go to Step 22

Go to Step 19

18

Inspect the MAP sensor for poor connections. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.

Did you find and correct the condition?

--

Go to Step 22

Go to Step 20

19

Inspect the PCM for poor connections. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.

Did you find and correct the condition?

--

Go to Step 22

Go to Step 21

20

Replace the MAP sensor. Refer to Manifold Absolute Pressure Sensor Replacement .

Did you complete the replacement?

--

Go to Step 22

--

21

Replace the PCM. Refer to Powertrain Control Module Replacement .

Did you complete the replacement?

--

Go to Step 22

--

22

  1. Use a scan tool in order to clear the DTCs.
  2. Turn OFF the ignition for 30 seconds.
  3. Start the engine.
  4. Operate the vehicle within the Conditions for Running the DTC.

Does the DTC run and pass?

--

Go to Step 23

Go to Step 2

23

With a scan tool, observe the stored information, Capture Info.

Does the scan tool display any DTCs that you have not diagnosed?

--

Go to Diagnostic Trouble Code (DTC) List

System OK