Refer to Engine Controls Schematic
Power, Ground, and Fuel Injectors
.
Circuit Description
The PCM controls the fuel injector control circuit using a Multi Function Driver (MFD). The MFD has the ability to detect an electrical malfunction. If an electrical malfunction is detected, the MFD signals the PCM to set this DTC.
Conditions for Running the DTC
The ignition is ON.
Conditions for Setting the DTC
| • | An incorrect voltage level is being detected on an injector driver circuit. |
| • | The above condition occurs for more than 30 seconds. |
Action Taken When the DTC Sets
| • | The PCM will illuminate the malfunction indicator lamp (MIL) during the second consecutive trip in which the diagnostic test has been run and failed. |
| • | The PCM will store conditions which were present when the DTC set as Freeze Frame/Failure Records data. |
Conditions for Clearing the MIL/DTC
| • | The PCM will turn OFF the malfunction indicator lamp (MIL) during the third consecutive trip in which the diagnostic has run and passed. |
| • | The history DTC will clear after 40 consecutive warm-up cycles have occurred without a malfunction. |
| • | The DTC can be cleared by using a scan tool. |
Diagnostic Aids
Inspect for the following conditions:
Important : Remove any debris from the connector surfaces before servicing a component. Inspect the connector gaskets when diagnosing or replacing a component. Ensure that the gaskets are installed correctly. The gaskets prevent contaminate intrusion.
| • | Faulty terminal connections |
| Inspect the harness connectors for backed-out terminals, improper mating, broken locks, improperly formed or damaged terminals, and faulty terminal-to-wire connections. Use a corresponding mating terminal to test for proper tension. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems. |
| • | A damaged harness |
| Inspect the wiring harness for damage. If the harness inspection does not reveal a problem, observe the display on the scan tool while moving connectors and wiring harnesses related to the sensor. A change in the scan tool display may indicate the location of the fault. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. |
| • | Inspect the PCM and the engine grounds for clean and secure connections. |
If the DTC is determined to be intermittent, reviewing the Failure Records can be useful in determining when the DTC was last set.
Test Description
The numbers below refer to the step numbers on the diagnostic table:
-
If the scan tool indicates STUCK HIGH there is a short to battery positive voltage on the fuel injector control circuit.
-
If the scan tool indicates STUCK LOW there is an open or a short to ground on the fuel injector control circuit.
-
When the multiple-way connector is disconnected, other DTCs will be set. These DTCs should be disregarded.
If the scan tool indicates a STUCK HIGH while cranking, the short to battery positive voltage is between the multiple-way connector and the PCM. If the scan tool indicates STUCK LOW while cranking the short to battery positive voltage is between the multiple-way connector and the fuel injector.
Important : While cranking the engine with the multiple-way connector disconnected, all of the other injector circuits should indicate STUCK LOW, this is a fault induced by disconnecting this connector. They will resume correct operation when the connector is reconnected.
-
This step is testing for a short to ground in the circuit.
-
The fuel injector in this circuit will need to be tested after the short to ground is repaired or after the PCM is replaced.
-
This step is testing the function of the PCM. If the test lamp flashes then the PCM is able to supply the ground.
-
This vehicle is equipped with a PCM which utilizes an Electronically Erasable Programmable Read Only Memory (EEPROM). When the PCM is replaced, the new PCM must be programmed.
Step | Action | Value(s) | Yes | No |
|---|---|---|---|---|
1 | Did you perform the Powertrain On Board Diagnostic (OBD) System Check? | -- | ||
2 | Start and idle the engine. Does scan tool indicate this DTC failed this ignition? | -- | ||
3 |
Does scan tool indicate this DTC failed this ignition? | -- | Go to Diagnostic Aids | |
With a scan tool, observe the Cyl. Injector Ckt. Status parameter for this injector. Does scan tool indicate this parameter STUCK HIGH? | -- | |||
Does the scan tool indicate this parameter STUCK LOW? | -- | Go to Diagnostic Aids | ||
|
Important : While cranking the engine with the multiple-way connector disconnected, all of the other injector circuits should indicate STUCK LOW, this is a fault induced by disconnecting this connector. They will resume correct operation when the connector is reconnected.
Does the scan tool indicate this parameter STUCK HIGH when the engine is cranking? | -- | |||
7 | Test for a short to voltage on the control circuit for this injector. Refer to Circuit Testing and Wiring Repairs . Did you find and correct the condition? | -- | ||
8 | Does the scan tool indicate this parameter STUCK LOW while cranking the engine? | -- | Go to Fuel Injector Solenoid Coil Test - Engine Coolant Temperature Between 10-35 Degrees C (50-95 Degrees F) or Fuel Injector Solenoid Coil Test - Engine Coolant Temperature Outside 10-35 Degrees C (50-95 Degrees F) | -- |
Does the test lamp illuminate? | -- | |||
Test for a short to ground on this injector control circuit. Refer to Circuit Testing and Wiring Repairs Did you find and correct the conditions? | -- | |||
Does the test lamp flash? | -- | Go to Fuel Injector Solenoid Coil Test - Engine Coolant Temperature Between 10-35 Degrees C (50-95 Degrees F) or Fuel Injector Solenoid Coil Test - Engine Coolant Temperature Outside 10-35 Degrees C (50-95 Degrees F) | ||
12 | Test for an open on this injector control circuit between the multiple-way connector and the PCM. Refer to Circuit Testing and Wiring Repairs . Did you find and correct the condition? | -- | ||
13 | Inspect the injector control circuit for a faulty connection at the PCM. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs . Did you find and correct the condition? | -- | ||
|
Important : The replacement PCM must be programmed. Replace the PCM. Refer to Powertrain Control Module Replacement/Programming . Did you complete the replacement? | -- | -- | ||
15 |
Does the DTC reset. | -- | System OK |
