Front Floor Console Replacement Pontiac

1. Position the front seats to the most rearward position.
2. Position the park brake lever to the full up position.
3. Remove the front floor console trim plate. Refer to Front Floor Console Trim Plate Replacement .
4. Remove the instrument panel accessory trim plate. Refer to Instrument Panel Accessory Trim Plate Replacement .
5. Remove the front floor console cup holder. Refer to Front Floor Console Cup Holder Replacement .
6. Lift up the front floor console armrest and remove the rubber mat from the storage compartment.
7. Remove the rear bolts from the front floor console storage compartment.
8. Remove the center bolts from the sides of the front floor console.
9. Remove the front screw covers at the front of the front floor console, using a small flat-bladed tool at the front edge.
10. Remove the front screws from the front floor console.
11. Remove the front nuts from the front floor console bracket.
12. Remove the front floor console, pulling up and rearward, guiding the park brake lever boot over the park brake lever.

1. Install the front floor console, sliding forward and donwward, guiding the park brake lever boot over the park brake lever.
2. Position and engage the front retainers by pressing inward, until the retainers are fully seated.

Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

3. Install the rear bolts to the front floor console storage compartment.

Tighten
Tighten the front floor console rear bolts to 10 N·m(89 lb in).

4. Install the center bolts to the sides of the front floor console.

Tighten
Tighten the front floor console center bolts to 10 N·m(89 lb in).

5. Install the front screws to the front floor console.

Tighten
Tighten the front floor console front screws to 2 N·m(18 lb in).

6. Install the front screw covers at the front of the front floor console, pressing into place until fully seated.
7. Install the front nuts to the front floor console bracket.

Tighten
Tighten the front floor console front nuts to 2 N·m(18 lb in).

8. Install the front floor console cup holder. Refer to Front Floor Console Cup Holder Replacement .
9. Install the instrument panel accessory trim plate. Refer to Instrument Panel Accessory Trim Plate Replacement .
10. Install the front floor console trim plate. Refer to Front Floor Console Trim Plate Replacement .
11. Release the park brake lever to the full down position.
12. Install the rubber mat to the storage compartment, and lower the front floor console armrest.
13. Reposition the front seats to the original position.

Front Floor Console Replacement Oldsmobile

1. Position the front seats to the most rearward position.
2. Position the park brake lever to the full up position.
3. Remove the front floor console trim plate. Refer to Front Floor Console Trim Plate Replacement .
4. Remove the instrument panel accessory trim plate. Refer to Instrument Panel Accessory Trim Plate Replacement .
5. Lift up the front floor console armrest and remove the rubber mat from the storage compartment.
6. Remove the rear bolts from the front floor console storage compartment.
7. Remove the center bolts from the sides of the front floor console.
8. Remove the front screw covers at the front of the front floor console, using a small flat-bladed tool at the front edge.
9. Remove the front screws from the front floor console.
10. Release the front retainers by pulling outward the front sides of the front floor console.
11. Remove the front floor console, pulling up and rearward, guiding the park brake lever boot over the park brake lever.

1. Install the front floor console, sliding forward and donwward, guiding the park brake lever boot over the park brake lever.
2. Position and engage the front retainers by pressing inward, until the retainers are fully seated.

Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

3. Install the rear bolts to the front floor console storage compartment.

Tighten
Tighten the front floor console rear bolts to 10 N·m(89 lb in).

4. Install the center bolts to the sides of the front floor console.

Tighten
Tighten the front floor console center bolts to 10 N·m(89 lb in).

5. Install the front screws to the front floor console.

Tighten
Tighten the front floor console front screws to 2 N·m(18 lb in).

6. Install the front screw covers at the front of the front floor console, pressing into place until fully seated.
7. Release the park brake lever to the full down position.
8. Install the instrument panel accessory trim plate. Refer to Instrument Panel Accessory Trim Plate Replacement .
9. Install the front floor console trim plate. Refer to Front Floor Console Trim Plate Replacement .
10. Install the rubber mat to the storage compartment, and lower the front floor console armrest.
11. Reposition the front seats to the original position.