Important: It is possible for the A/C to disengage while the LED is on in the following conditions, wide open throttle or a A/C system over pressure situation.
Important: Recirculation reuses interior air and is therefore not recommended for long periods owing to a build up of carbon dioxide from occupants exhaling. If recirculation mode is used for an extended period of time about 30 minutes, the system will automatically select fresh air mode to let some fresh air into the cabin for ventilation then return to recirculation mode.
The A/C switch is on (4). The fan switch is set to any one of twenty speeds (1). The temperature switch is set to the full cold position (2). The mode control switch is set to face mode (3). The recirculation door (6) is closed, allowing outside air (5) to enter and flow into the HVAC module assembly via the plenum chamber inlet. Air is drawn into the HVAC module assembly by the blower motor (7) and is then forced through the cold evaporator fins (8). In full cold mode, the air mix doors (13) are fully closed, sealing off the passage through the heater core (11). The air travels through the open face/foot door (10). The cold air (14) is then directed through the centre and side vents.
The fan switch is set to any one of twenty speeds (1). The temperature switch is set to the full hot position (2). The mode control switch is set to face mode (3). The recirculation door (6) is closed, allowing outside air (5) to enter and flow into the HVAC module assembly via the plenum chamber inlet . Air is drawn into the HVAC module assembly by the blower motor (7). This air is then forced through the evaporator core fins (8). In full heat mode, the air mix doors (13) are fully open, directing all incoming air through the heater core (11). The air travels through the open face/foot door (10). The heated air (14) is then directed out of the HVAC module assembly to the centre and side vents.
The A/C switch is on (4). The fan switch is set to any one of twenty speeds (1). The temperature switch is set to the full cold position (2). The mode control switch is set to bi-level mode (3). The recirculation door (6) is closed allowing outside air (5) to enter and flow into the HVAC module assembly via the plenum chamber inlet . Air is drawn into the HVAC module assembly by the blower motor (7), and is then forced through the cold evaporator fins (8). In full cold mode, the air mix doors (13) are fully closed sealing off the passage through the heater core (11). The air travels through the opened face/foot door (10) and then through the defrost/floor door (9), which is fully open in the floor mode. The cold air (14) is then directed through the centre and side vents as well as the floor ducts.
The fan switch is set to any one of twenty speeds (1). The temperature switch is set to the full hot position (2). The mode control switch is set to bi-level mode (3). The recirculation door (6) is closed, allowing outside air (5) to enter and flow into the HVAC module assembly via the plenum chamber inlet. Air is drawn into the HVAC module assembly by the blower motor (7). This air is then forced through the evaporator core fins (8). In full heat mode, the air mix doors (13) are fully open, directing all incoming air through the heater core (11). The air travels through the half opened face door (10) and through the defrost / floor door (9), which is fully open in the floor mode. The heated air (14) is then directed through the centre and side vents as well as to the floor ducts.
The A/C switch is on (4). The fan switch is set to any one of twenty speeds (1). The temperature switch is set to the full cold position (2). The mode control switch is set to floor mode (3). The recirculation door (6) is closed, allowing outside (5) air to enter and flow into the HVAC module assembly via the plenum chamber inlet. Air is drawn into the HVAC module assembly by the blower motor (7), and is then forced through the cold evaporator fins (8). In full cold mode, the air mix doors (13) are fully closed, sealing off the passage through the heater core (11). The air travels through the face/ floor door (10), which is fully open in the floor mode. The cold air (14) is then directed to floor ducts.
The fan switch is set to any one of twenty speeds (1). The temperature switch is set to the full hot position (2). The mode control switch is set to floor mode (3). The recirculation door (4) is closed, allowing outside air (5) to enter and flow into the HVAC module assembly via the plenum chamber inlet. Air is drawn into the HVAC module assembly by the blower motor (7). This air is then forced through the evaporator core fins (8). In full heat mode, the air mix doors (13) are fully open, directing all incoming air through the heater core (11). The air travels through the face/ floor door (10), which is fully open in the floor mode. The heated air (14) is then directed to the floor ducts.
The A/C switch is on (4). The fan switch is set to any one of twenty speeds (1). The temperature switch is set to the full hot position (2). The mode control switch is set to defrost mode (3). The recirculation door (6) is closed, allowing outside air (5) to enter and flow into the HVAC module assembly via the plenum chamber inlet. Air is drawn into the HVAC module assembly by the blower motor (7). This air is then forced through the cold evaporator core fins (8) removing moisture from the air. In full heat mode, the air mix doors (13) are fully open, allowing dehumidified incoming air through the heater core (11). The air travels through the defrost door (9), which is fully open in the defrost mode. The heated air (14) is then directed to the front windscreen via the defrost outlets.
