GM Service Manual Online
For 1990-2009 cars only

Diagnostic Instructions

    • Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure.
    • Review Strategy Based Diagnosis for an overview of the diagnostic approach.
    •  Diagnostic Procedure Instructions provides an overview of each diagnostic category.

DTC Descriptors

DTC P0135:  HO2S Heater Performance Sensor 1

DTC P0141:  HO2S Heater Performance Sensor 2

Diagnostic Fault Information

Circuit

Short to Ground

Open/High Resistance

Short to Voltage

Signal Performance

Ignition 1 Voltage

P0135, P0141

P0135, P0141

--

--

HO2S 1 Heater Control

P0135

P0135

P0135

--

HO2S 2 Heater Control

P0141

P0141

P0141

--

Circuit Description

The heated oxygen sensors (HO2S) are used for fuel control and post catalyst monitoring. Each HO2S compares the oxygen content of the surrounding air with the oxygen content in the exhaust stream. The HO2S must reach operating temperature to provide an accurate voltage signal. A heating element inside the HO2S minimizes the time required for the sensor to reach operating temperature. Voltage is provided to the heater by the ignition 1 voltage circuit through a fuse. Ground is provided to the heater on the low control circuit by a low side driver within the control module. The control module monitors the current draw of the heater to determine if a failure is present.

The HO2S utilizes the following circuits:

    • A signal circuit
    • A low reference circuit
    • An ignition 1 voltage circuit
    • A heater control circuit

Conditions for Running the DTC

P0135

    • DTCs P0107, P0108, P0117, P0118 are not set.
    • The engine has been operating for 3 minutes.
    • The DTC runs continuously when the above conditions are met.

P0141

    • The ignition 1 voltage is greater than 10 volts.
    • The engine has been operating for 30 seconds.
    • The DTCs run continuously when the above conditions.

Conditions for Setting the DTC

P0135

The ECM detects that the HO2S 1 heater current is less than 0.1 amps for 3 seconds.

P0141

The ECM detects that the HO2S 2 heater current is less than 0.1 amps for 13 seconds.

Action Taken When the DTC Sets

DTCs P0135 and P0141 are Type B DTCs.

Conditions for Clearing the MIL/DTC

DTCs P0135 and P0141 are Type B DTCs.

Reference Information

Schematic Reference

Engine Controls Schematics

Connector End View Reference

Component Connector End Views

Electrical Information Reference

    •  Circuit Testing
    •  Connector Repairs
    •  Testing for Intermittent Conditions and Poor Connections
    •  Wiring Repairs

DTC Type Reference

Powertrain Diagnostic Trouble Code (DTC) Type Definitions

Scan Tool Reference

Control Module References for scan tool information

Circuit/System Verification

    Important: It may take up to 8 minutes for the DTC to set.

  1. Engine at normal operating temperature, operate the engine above 1,200 RPM for 30 seconds and then allow the engine to idle. DTC P0135 or P0141 should not set.
  2. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the conditions that you observed from the Freeze Frame/Failure Records data.

Circuit/System Testing

  1. Ignition OFF, disconnect the harness connector at the appropriate H02S.
  2. Ignition ON, verify that a test lamp illuminates between the ignition 1 voltage circuit terminal 2 and ground.
  3. Important: The ignition 1 voltage circuit supplies voltage to other components. Make sure you test all circuits for a short to ground or test all components for being shorted that share the ignition 1 voltage circuit.

    If the test lamp does not illuminate, test the ignition 1 voltage circuit for a short to ground or an open/high resistance. If the circuit tests normal and the ignition 1 voltage circuit fuse is open, test all components connected to the ignition 1 voltage circuit and replace as necessary.
  4. Ignition OFF, connect a test lamp between the control circuit terminal 3 and B+. The test lamp should not illuminate.
  5. If test lamp is always ON, test the control circuit for a short to ground. If the circuit tests normal, replace the ECM.
  6. Engine running, verify the test lamp illuminates or flashes.
  7. If the test lamp is always OFF, test the control circuit for a short to voltage or an open/high resistance. If the circuit tests normal, replace the ECM.
  8. If all circuits test normal, test or replace the H02S sensor.

Component Testing

  1. Ignition OFF, disconnect the harness connector at the heated oxygen sensor (HO2S).
  2. Test for 3-35 ohms of resistance between terminals 2 and 3.
  3. If not within the specified range, replace the HO2S.

Repair Instructions

Perform the Diagnostic Repair Verification after completing the diagnostic procedure.

    •  Heated Oxygen Sensor 1 Replacement
    •  Heated Oxygen Sensor 2 Replacement
    •  Control Module References for engine control module replacement, setup, and programming