GM Service Manual Online
For 1990-2009 cars only

Diagnostic Instructions

    • Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure.
    • Review Strategy Based Diagnosis for an overview of the diagnostic approach.
    •  Diagnostic Procedure Instructions provides an overview of each diagnostic category.

DTC Descriptor

DTC P0106: Manifold Absolute Pressure (MAP) Sensor Performance

Diagnostic Fault Information

Circuit

Short to Ground

Open/High Resistance

Short to Voltage

Signal Performance

5-Volt Reference

P0107

P0107

P0108

P0106

MAP Sensor Signal

P0107

P0107

P0108

P0106

Low Reference

--

P0107

--

P0106

Typical Scan Tool Data

MAP Sensor

Circuit

Short to Ground

Open

Short to Voltage

Operating Conditions: Engine operating in Closed Loop.

Parameter Normal Range: 32-42 kPa

5-Volt Reference

10 kPa

10 kPa

104 kPa

MAP Sensor Signal

10 kPa

10 kPa

104 kPa*

Low Reference

--

10 kPa

--

* Internal ECM damage may occur if the circuit is shorted to B+.

Circuit/System Description

The manifold absolute pressure (MAP) sensor responds to pressure changes in the intake manifold. The pressure changes occur based on the engine load. The engine control module (ECM) supplies 5 volts to the MAP sensor on the 5-volt reference circuit. The ECM provides a ground on the low reference circuit. The MAP sensor provides a signal to the ECM on the MAP sensor signal circuit which is relative to the pressure changes in the manifold. The ECM detects a low signal voltage at a low MAP, such as during an idle or a deceleration. The ECM detects a high signal voltage at a high MAP, such as the ignition is ON, with the engine OFF, or at a wide open throttle (WOT). The MAP sensor is also used to determine the barometric pressure (BARO). This occurs when the ignition switch is turned ON, with the engine OFF. The BARO reading may also be updated whenever the TP sensor is greater than 28 percent.

Condition for Running the DTC

    • DTCs P0107, P0108, P0117, P0118, P0122, P0123, P0201, P0202, P0203, P0204, P0300, P0351, P0352, P0401, P0402, P0404, P0405, P0406, P042E, P0506, and P0507 are not set.
    • The engine is running.
    • Valid barometric pressure (BARO) update.
    • The traction control is not active.
    • The torque converter clutch (TCC) is steady (A/T).
    • The A/C compressor clutch is steady.
    • The coolant temperature is greater than -10°C (+14°F).
    •  The engine speed is between 1,300-4,500 RPM.
    • The change in engine speed is less than 200 RPM.
    • The change in idle air is less than 5 percent.
    • The change in throttle position (TP) is less than 3 percent, or the change in MAP is less than 5 percent.
    • The change in exhaust gas recirculation (EGR) position is less than 6 percent.
    • The above conditions are stabilized for 1.5 seconds.
    • DTC P0106 runs continuously when the above conditions are met.

Conditions for Setting the DTC

The ECM detects that the actual MAP signal is not within the predicted range for greater than 25 seconds.

Action Taken When the DTC Sets

DTC P0106 is a Type B DTC.

Conditions for Clearing the MIL/DTC

DTC P0106 is a Type B DTC.

Diagnostic Aids

With the ignition ON and the engine stopped, the manifold pressure is equal to atmospheric pressure and the signal voltage will be high. This information is used by the ECM as an indication of vehicle altitude. Comparison of this reading with a known good vehicle with the same sensor is a good way to check the accuracy of a suspect sensor. Readings should be the same +0.4 volt.

The MAP sensor vacuum source should be thoroughly inspected for restrictions at the intake manifold.

Reference Information

Schematic Reference

Engine Controls Schematics

Connector End View Reference

Component Connector End Views

Electrical Information Reference

    •  Circuit Testing
    •  Connector Repairs
    •  Testing for Intermittent Conditions and Poor Connections
    •  Wiring Repairs

DTC Type Reference

Powertrain Diagnostic Trouble Code (DTC) Type Definitions

Scan Tool Reference

Control Module References for scan tool information

Special Tools

J 23738-A Mityvac

Circuit/System Verification

  1. Engine running, observe the scan tool MAP Sensor parameter. The reading should be between 32-42 kPa.
  2. Important: The vehicle used for the comparison is not limited to the same type of vehicle being serviced. A vehicle known to provide an accurate reading is acceptable.

  3. Ignition ON, engine OFF, compare the MAP sensor pressure parameter to the pressure parameter of a known good vehicle. The reading should be within 3 kPa of the known good vehicle.
  4. Important: The Altitude vs Barometric Pressure table indicates a pressure range for a given altitude under normal weather conditions. Weather conditions consisting of very low or very high pressure and/or very low or very high temperature may cause a reading to be slightly out of range.

  5. Compare the MAP sensor pressure parameter to the reading in the Altitude Versus Barometric Pressure. The MAP sensor pressure parameter should be within the specified range indicated on the table.
  6. Start the engine, the scan tool MAP sensor pressure parameter should change while starting the engine.
  7. Engine running, snap the throttle while observing the MAP sensor pressure parameter on the scan tool. The MAP sensor pressure parameter should change rapidly when the throttle position changes.

Circuit/System Testing

  1. Verify none of the following conditions exist:
  2. • Vacuum leaks or restrictions at the MAP sensor.
    • Engine vacuum leaks
    • Restricted exhaust--Refer to Restricted Exhaust.
    • Worn piston rings--Refer to Engine Compression Test.
    • Incorrect cam timing--Refer to Timing Belt Inspection.
  3. Ignition OFF, disconnect the harness connector at the throttle body assembly.
  4. Ignition OFF, test for less than 5 ohms of resistance between the low reference circuit terminal 1 and ground.
  5. If greater than specified range, test the low reference circuit for an open/high resistance. If the circuit tests normal, replace the ECM.

    Important: The 5-volt reference circuits are internally and externally connected at the ECM. Other component DTCs may be set. If other DTCs are set, review the electrical schematic and diagnose the applicable circuits and components.

  6. Ignition ON, test for 4.8-5.2 volts between the 5-volt reference circuit terminal 2 and ground.
  7. If less than the specified range, test the 5-volt reference circuit for a short to ground or open/high resistance. If the circuit tests normal, replace the ECM.
    If greater than the specified range, test the 5-volt reference circuit for a short to voltage. If the circuit tests normal, replace the ECM.
  8. Verify the scan tool TP sensor voltage parameter is less than 0.3 volt.
  9. If greater than the specified range, test the signal circuit for a short to voltage. If the circuit tests normal, replace the ECM.
  10. Install a 3A fused jumper wire between the signal circuit terminal 3 and the 5-volt reference circuit terminal 2. Verify the scan tool TP sensor voltage parameter is greater than 4.8 volts.
  11. If less than the specified range, test the signal circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the ECM.
  12. Ignition OFF, connect the harness connector of the throttle body assembly.
  13. Disconnect the harness connector at the MAP sensor.
  14. Ignition OFF, test for less than 5 ohms of resistance between the low reference circuit terminal 3 and ground.
  15. If greater than specified range, test the low reference circuit for an open/high resistance. If the circuit tests normal, replace the ECM.
  16. Ignition ON, verify the scan tool MAP sensor parameter is less than 12 kPa.
  17. If greater than the specified range, test the signal circuit for a short to voltage. If the circuit tests normal, replace the ECM.

    Important: The 5-volt reference circuits are internally and externally connected at the ECM. Other component DTCs may be set. If other DTCs are set, review the electrical schematic and diagnose the applicable circuits and components.

  18. Test for 4.8-5.2 volts between the 5-volt reference circuit terminal 1 and ground.
  19. If less than the specified range, test the 5-volt reference circuit for a short to ground or open/high resistance. If the circuits tests normal, replace the ECM.
    If greater than the specified range, test the 5-volt reference circuit for a short to voltage. If the circuit tests normal, replace the ECM.
  20. Install a 3A fused jumper wire between the signal circuit terminal 2 and the 5-volt reference circuit terminal 1. Verify the scan tool MAP sensor pressure parameter is greater than 102 kPa.
  21. If less than the specified range, test the signal circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the ECM.
  22. If all circuits test normal, test or replace the MAP sensor.

Component Testing

TP Sensor

  1. Ignition OFF, disconnect the harness connector at the throttle body assembly.
  2. Test for 1160-1175 ohms between the 5-volt reference terminal 2 and the low reference terminal 1.
  3. If not within the specified range, replace the throttle body assembly.
  4. Sweep the TP sensor through the entire range while monitoring the resistance between the signal terminal 3 and the low reference terminal 1. The resistance should vary between 1530-630 ohms without any spikes or dropouts.
  5. If not within the specified range or is erratic, replace the throttle body assembly.
  6. Sweep the TP sensor through the entire range while applying 5 volts and ground to the applicable terminals. Test the voltage between the signal terminal 3 and the low reference terminal 1. The voltage should vary between 4.3-0.6 volts without any spikes or dropouts.
  7. If not within the specified range or is erratic, replace the throttle body assembly.

MAP Sensor

  1. Ignition OFF, perform one of the following applicable procedures.
  2. • Disconnect the vacuum supply hose from the MAP sensor
    • Remove the MAP sensor from the intake manifold
  3. Ignition ON, observe and record the scan tool MAP sensor pressure data parameter. This is the first MAP sensor reading.
  4. With the J 23738-A , apply 17 kPa (5 in Hg) of vacuum to the MAP sensor. Observe and record the scan tool MAP sensor pressure data parameter. This is the second MAP sensor reading.
  5. Subtract the second MAP sensor reading from the first MAP sensor reading. Verify that the vacuum decrease is within 4 kPa (1 in Hg) of the applied vacuum.
  6. If not within the specified range, replace the MAP sensor.
  7. With the J 23738-A , apply 34 kPa (10 in Hg) of vacuum to the MAP sensor. Observe and record the scan tool MAP sensor pressure data parameter. This is the third MAP sensor reading.
  8. Subtract the third MAP sensor reading from the first MAP sensor reading. Verify that the vacuum decrease is within 4 kPa (1 in Hg) of the applied vacuum.
  9. If not with in the specified range, replace the MAP sensor.

Repair Instructions

Perform the Diagnostic Repair Verification after completing the diagnostic procedure.

    •  Manifold Absolute Pressure Sensor Replacement
    •  Throttle Position Sensor Replacement
    •  Control Module References for engine control module replacement, setup, and programming