Front Floor Console Replacement LHD

1. Remove the side trim plate - Console. Refer to Console Trim Plate Replacement .
2. Remove the centre console end panel. Refer to Center Console End Panel Replacement .
3. Remove the armrest assembly. Refer to Front Floor Console Armrest Replacement .
4. Remove the centre console cupholder. Refer to Front Floor Console Cup Holder Replacement .
5. Remove the trim plate - Console. Refer to Console Trim Plate Replacement .




Important: The following procedure is carried out on the right side of the centre console.

6. Remove the retaining screws from the centre console (3).
7. Remove the rear centre console retaining bolt (4).
8. Remove the park recess tray retaining screws (1) and retaining clip (2).



9. Loosen the centre console to park brake assembly bracket retaining bolts (1).




Important: The following procedures are carried out on the left hand side.

10. Remove the rear centre console retaining bolt (2).
11. Remove the centre console retaining screws (3).
12. Remove the coin holder retaining screws (1) and retaining clip (4).



13. Remove the park brake warning lamp switch (2) retaining torx screw (3).
14. Loosen the centre console retaining bolts (1).



15. Remove the coin holder upper retaining screws (2,4) and remove the coin holder (3).
16. Remove the park brake recess tray upper retaining screw (2) and remove the park brake recess (3).



17. Remove the centre console top retaining screws (1).



18. Remove the lower centre console retaining bolts (1).



19. Disconnect the centre console electrical connectors (1,3).
20. Detach and remove the centre console electrical connectors (4,2).



21. Remove the centre console (1).



22. Remove the adjuster circlip (2) from the park brake adjuster (1).
23. Remove the park brake adjuster (1), by rotating counter clockwise until it leaves the retaining nut insert (2).
24. Remove the park brake adjuster (1) retaining nut insert (3).

Important:  If replacing the park brake assembly. Refer to Parking Brake Release Handle Assembly Replacement .

25. Remove the park brake assembly (4).

1. Align the park brake assembly (4) with the transmission tunnel.
2. Install the park brake adjuster nut insert (3) into the park brake assembly (4).
3. Install the park brake adjuster (1) by rotating it clockwise until the desired tension is reached.
4. Once the desire tension is reached install the park adjuster circlip (2).
5. Align the centre console over the park brake assembly.



6. Attach and remove the centre console electrical connectors (4,2).
7. Connect the centre console electrical connectors (1,3).
8. Install the centre console cupholder. Refer to Front Floor Console Cup Holder Replacement .

Notice: Refer to Fastener Notice in the Preface section.




9. Install the lower centre console retaining screws (1).

Tighten
Tighten the screws (1) to 2  N·m (18 lb in).




10. Install the upper centre console retaining screws (1).

Tighten
Tighten the screws (1) to 2  N·m (18 lb in).




11. Install the coinholder (3) and park brake recess trim (1).
12. Install the coinholder and park brake recess trim upper retaining screws (2,4).

Tighten
Tighten the screws (2,4) to 2  N·m (18 lb in).




13. Install the park brake warning lamp switch (2).
14. Install the park brake warning lamp switch retaining torx screw (3).
15. Tighten the centre console to park brake assembly retaining bolts (1).

Tighten
Tighten the bolts to 25  N·m (18 lb ft).




16. Install the rear centre console retaining bolt (2).

Tighten
Tighten the bolt to 25  N·m (18 lb ft).

17. Install the centre console retaining screws (3).

Tighten
Tighten the screws (3) to 2  N·m (18 lb in).

18. Install the coinholder lower retaining screws (1) and retaining clip (4).

Tighten
Tighten the screws (1) to 2  N·m (18 lb in).




19. Tighten the centre console to park brake assembly retaining bolts (1).

Tighten
Tighten the bolts to 25  N·m (18 lb ft).




20. Install the centre console retaining screws (3).

Tighten
Tighten the screws (3) to 2  N·m (18 lb in).

21. Install the park brake recess lower retaining screws (1) and retaining clip (2).

Tighten
Tighten the screws (1) to 2  N·m (18 lb in).

22. Tighten the rear centre console retaining bolt (4).

Tighten
Tighten the bolt to 25  N·m (18 lb ft).

23. Install the trim plate - Console. Refer to Console Trim Plate Replacement .
24. Install the armrest assembly. Refer to Front Floor Console Armrest Replacement .
25. Install the centre console end panel. Refer to Center Console End Panel Replacement .
26. Install the side trim plate - Console. Refer to Front Floor Console Side Trim Panel Replacement - Right Side .
27. Test all electrical components for correct operation.

Front Floor Console Replacement RHD

1. Remove the side trim plate - Console. Refer to Console Trim Plate Replacement .
2. Remove the centre console end panel. Refer to Center Console End Panel Replacement .
3. Remove the armrest assembly. Refer to Front Floor Console Armrest Replacement .
4. Remove the trim plate - console. Refer to Console Trim Plate Replacement .
5. Remove the centre console cupholder. Refer to Front Floor Console Cup Holder Replacement .




Important: The following procedure is carried out on the right side of the centre console.

6. Remove the retaining screws from the centre console (3).
7. Remove the rear centre console retaining bolt (4).
8. Remove the park recess tray retaining screws (1) and retaining clip (2).



9. Loosen the centre console to park brake assembly bracket retaining bolts (1).




Important: The following procedures are carried out on the left hand side.

10. Remove the rear centre console retaining bolt (2).
11. Remove the centre console retaining screws (3).
12. Remove the coin holder retaining screws (1) and retaining clip (4).



13. Remove the park brake warning lamp switch (2) retaining torx screw (3).
14. Loosen the centre console retaining bolts (1).



15. Remove the coin holder upper retaining screws (2,4) and remove the coin holder (1).
16. Remove the park brake recess tray upper retaining screw (2) and remove the recess trim (3).



17. Remove the centre console top retaining screws (1).



18. Remove the lower centre console retaining bolts (1).



19. Disconnect the centre console electrical connectors (1,3).
20. Detach and remove the centre console electrical connectors (4,2).



21. Remove the centre console (1).



22. Remove the adjuster circlip (2) from the park brake adjuster (3).
23. Remove the park brake adjuster (3), by rotating counter clockwise until it leaves the retaining nut insert (1).
24. Remove the park brake adjuster (3) retaining nut insert (1).

Important:  If replacing the park brake assembly. Refer to Parking Brake Release Handle Assembly Replacement .

25. Remove the park brake assembly (4).

1. Align the park brake assembly (4) with the transmission tunnel.
2. Install the park brake adjuster nut insert (1) into the park brake assembly (4).
3. Install the park brake adjuster (3) by rotating it clockwise until the desired tension is reached.
4. Once the desired tension is reached install the park adjuster circlip (2).
5. Align the centre console over the park brake assembly.



6. Attach and remove the centre console electrical connectors (4,2).
7. Connect the centre console electrical connectors (1,3).
8. Install the centre console cupholder. Refer to Front Floor Console Cup Holder Replacement .

Notice: Refer to Fastener Notice in the Preface section.




9. Install the lower centre console retaining screws (1).

Tighten
Tighten the screws (1) to 2  N·m (18 lb in).




10. Install the upper centre console retaining screws (1).

Tighten
Tighten the screws (1) to 2  N·m (18 lb in).




11. Install the coinholder (1) and park brake recess trim (3).
12. Install the coinholder and park brake recess trim upper retaining screws (2,4).

Tighten
Tighten the screws (2,4) to 2  N·m (18 lb in).




13. Install the park brake warning lamp switch (2).
14. Install the park brake warning lamp switch retaining torx screw (3).
15. Tighten the centre console to park brake assembly retaining bolts (1).

Tighten
Tighten the bolts to 25  N·m (18 lb ft).




16. Install the rear centre console retaining bolt (2).

Tighten
Tighten the bolt to 25  N·m (18 lb ft).

17. Install the centre console retaining screws (3).

Tighten
Tighten the screws (3) to 2  N·m (18 lb in).

18. Install the coinholder lower retaining screws (1) and retaining clip (4).

Tighten
Tighten the screws (1) to 2  N·m (18 lb in).




19. Tighten the centre console to park brake assembly retaining bolts (1).

Tighten
Tighten the bolts to 25  N·m (18 lb ft).




20. Install the centre console retaining screws (3).

Tighten
Tighten the screws (3) to 2  N·m (18 lb in).

21. Install the park brake recess lower retaining screws (1) and retaining clip (2).

Tighten
Tighten the screws (1) to 2  N·m (18 lb in).

22. Tighten the rear centre console retaining bolt (4).

Tighten
Tighten the bolt to 25  N·m (18 lb ft).

23. Install the trim plate - Console. Refer to Console Trim Plate Replacement .
24. Install the armrest assembly. Refer to Front Floor Console Armrest Replacement .
25. Install the centre console end panel. Refer to Center Console End Panel Replacement .
26. Install the side trim plate - Console. Refer to Console Trim Plate Replacement .
27. Test all electrical components for correct operation.