GM Service Manual Online
For 1990-2009 cars only

Diagnostic Instructions

    • Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure.
    • Review Strategy Based Diagnosis for an overview of the diagnostic approach.
    •  Diagnostic Procedure Instructions provides an overview of each diagnostic category.

Diagnostic Fault Information

Circuit

Short to Ground

Open/High Resistance

Short to Voltage

Signal Performance

Rear Fog Lamp Relay B+

--

1

1

--

Rear Fog Lamp Switch Signal

2

2

2

--

Rear Fog Lamp Relay Control

1

1

1

--

Rear Fog Lamp Control

1

1

1

--

Rear Fog Lamp Ground

--

1

--

--

Rear Fog Lamp Switch Ground

--

2

--

--

1. Rear Fog Lamps Malfunction

2. Rear Fog Lamp Switch Malfunction

Circuit/System Description

The rear fog lamp relay is supplied with battery voltage at all times. The rear fog lamp switch signal circuit is grounded momentarily by pressing the rear fog lamp switch. The body control module (BCM) energizes the rear fog lamp relay by applying ground to the rear fog lamp relay control circuit. When the rear fog lamp relay is energized, the relay switch contacts close and battery voltage is applied through the rear fog lamp supply voltage circuit which illuminates the rear fog lamp.

Reference Information

Schematic Reference

Exterior Lights Schematics

Connector End View Reference

Component Connector End Views

Description and Operation

Exterior Lighting Systems Description and Operation

Electrical Information Reference

    •  Circuit Testing
    •  Connector Repairs
    •  Testing for Intermittent Conditions and Poor Connections
    •  Wiring Repairs

Scan Tool Reference

Control Module References for scan tool information

Circuit/System Verification

Ignition ON, observe the scan tool Rear Fog Light Switch parameter while turning the front fog lamp switch ON and OFF. The parameter should change between Active and Inactive.

If the parameter does not change between the commanded states, refer to Rear Fog Lamp Switch Malfunction.
If the parameter changes between the commanded states, refer to Rear Fog Lamp Malfunction.

Circuit/System Testing

Rear Fog Lamp Switch Malfunction

  1. Ignition OFF, disconnect the harness connector at the headlamp and panel dimmer switch.
  2. Ignition OFF, test for less than 5 ohms between the ground circuit terminal 4 and ground.
  3. If greater than the specified range, test the ground circuit for an open/high resistance.
  4. Ignition ON, verify the scan tool Rear Fog Light Switch parameter is Inactive.
  5. If not the specified value, test the signal circuit terminal 2 for a short to ground. If the circuit tests normal, replace the BCM.
  6. Install a 3A fused jumper wire between the signal circuit terminal 2 and the ground circuit terminal 4. Verify the scan tool Rear Fog Light Switch parameter is Active.
  7. If not the specified value, test the signal circuit for a short to voltage or an open/high resistance. If the circuit tests normal, replace the BCM.
  8. If all circuits test normal, test or replace the headlamp and panel dimmer switch.

Rear Fog Lamp Malfunction

  1. Ignition OFF, disconnect the rear fog lamp relay.
  2. Ignition ON, verify that a test lamp does not illuminate between the control circuit terminal 87 and ground.
  3. If the test lamp illuminates, test the control circuit for a short to voltage.
  4. Verify that a test lamp illuminates between the B+ circuit terminal 30 and ground.
  5. If the test lamp does not illuminate, test the B+ circuit for a short to ground or an open/high resistance.
  6. Verify that a test lamp illuminates between the B+ circuit terminal 85 and ground.
  7. If the test lamp does not illuminate, test the B+ circuit for an open/high resistance.
  8. Disconnect the harness connector at the rear fog lamp.
  9. Ignition OFF, test for less than 5 ohms between the ground circuit terminal 8 and ground.
  10. If greater than the specified range, test the ground circuit for an open/high resistance.
  11. Connect the harness connector at the rear fog lamp.
  12. Connect a 10A fused jumper wire between the B+ circuit terminal 30 and the control circuit terminal 87. Verify the rear fog lamp illuminates.
  13. If the rear fog lamp does not illuminate, test the control circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the rear fog lamp.
  14. Connect a test lamp between the B+ circuit terminal 85 and the control circuit terminal 86.
  15. Command the rear fog lamp ON and OFF with the rear fog lamp switch. The test lamp should turn ON and OFF when changing between the commanded states.
  16. If the test lamp is always ON, test the control circuit for a short to ground. If the circuit tests normal, replace the BCM.
    If the test lamp is always OFF, test the control circuit for a short to voltage or open/high resistance. If the circuit tests normal, replace the BCM.
  17. If all circuits test normal, test or replace the rear fog lamp relay.

Rear Fog Lamp Indicator Malfunction

Ignition ON, with a scan tool perform the Display Tests for the instrument panel cluster (IPC) and observe the fog lamp indicator.

If the rear fog lamp indicator illuminates during the test, replace the BCM.
If the rear fog lamp indicator does not illuminate during the test or remains illuminated at all times, replace the IPC.

Repair Instructions

Perform the Diagnostic Repair Verification after completing the diagnostic procedure.

    •  Headlamp Switch Replacement
    •  Rear Fog Lamp Replacement
    •  Underhood Electrical Center or Junction Block Replacement
    •  Control Module References for BCM or IPC replacement, setup, and programming