GM Service Manual Online
For 1990-2009 cars only

Tools Required

   • 
  • EN 46106 Flywheel Holding Tool
  •    • 
  • EN 46110 On-Vehicle Valve Spring Compressor
  •    • 
  • EN 46116 Valve Stem Seal Remover/Installer
  •    • 
  • J 39313 Spark Plug Port Adapter
  •    • 
  • EN 46117 Valve Collet Remover/Installer
  • Removal Procedure

    1. Remove the starter motor. Refer to Starter Motor Replacement.

    2. Object Number: 1958097  Size: SH

      Important: If the EN 46106  (1) is not installed, the crankshaft may rotate. If the crankshaft rotates, disassembly and reassembly of the entire camshaft timing system may be required.

    3. Install the EN 46106  (1) in order to prevent crankshaft rotation.
    4. Remove the camshafts and rocker arms. Refer to Camshaft Replacement - Left Side.
    5. Remove the spark plug from the applicable cylinder. Refer to Spark Plug Replacement.
    6. Install the J 39313 to the applicable cylinder.
    7. Connect the J 39313 to a compressed air source.
    8. Install the EN 46110 above the applicable cylinder.

    9. Object Number: 1961752  Size: SH
    10. Install the EN 46110 to cylinder head retaining bolts (1)
    11. Tighten the EN 46110 valve spring compressor nut (2).

    12. Object Number: 1958055  Size: SH
    13. Remove the valve collets using the EN 46117 .

    14. Object Number: 1961752  Size: SH
    15. Loosen the EN 46110 valve spring compressor nut (2).
    16. Remove the EN 46110 to cylinder head retaining bolts (1).
    17. Remove the EN 46110 .

    18. Object Number: 1958058  Size: SH
    19. Remove the valve spring retainer (1).
    20. Remove the valve spring (2).

    21. Object Number: 1960693  Size: SH

      Important: NEVER reuse a valve stem oil seal.

    22. Remove the valve stem oil seal (2) using the EN 46116  (1).
    23. Discard the valve stem oil seals.

    24. Repeat these procedures for the remaining valves.

    Installation Procedure


      Object Number: 1960693  Size: SH
    1. Use the EN 46116  (1) in order to install the NEW valve stem seal (2).

    2. Object Number: 1958058  Size: SH
    3. Install the valve spring (2).
    4. Install the valve spring retainer (1).

    5. Object Number: 1961752  Size: SH
    6. Install the EN 46110 above the applicable valve spring.
    7. Install the EN 46110 to cylinder head retaining bolts (1)
    8. Tighten the EN 46110 valve spring compressor nut (2).

    9. Object Number: 1958055  Size: SH
    10. Install the valve collets using the EN 46117  (1).

    11. Object Number: 1961752  Size: SH
    12. Loosen the EN 46110 valve spring compressor nut (2).
    13. Remove the EN 46110 to cylinder head retaining bolts (1).
    14. Remove the EN 46110
    15. Disconnect the J 39313 from the compressed air source.
    16. Remove the J 39313 .
    17. Install the spark plugs. Refer to Spark Plug Replacement.
    18. Install the rocker arms and camshafts. Refer to Camshaft Replacement - Left Side.

    19. Object Number: 1958097  Size: SH
    20. Remove the EN 46106  (1).
    21. Install the starter motor. Refer to Starter Motor Replacement.