GM Service Manual Online
For 1990-2009 cars only

Diagnostic Instructions

    • Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure.
    • Review Strategy Based Diagnosis for an overview of the diagnostic approach.
    •  Diagnostic Procedure Instructions provide an overview of each diagnostic category.

DTC Descriptors

DTC P0130: HO2S Circuit Closed Loop (CL) Performance Bank 1 Sensor 1

DTC P0150: HO2S Circuit Closed Loop (CL) Performance Bank 2 Sensor 1

Diagnostic Fault Information

Circuit

Short to Ground

Open/High Resistance

Short to Voltage

Signal Performance

HO2S Bank 1 Sensor 1 Signal

P0131

P0130, P0134

P0132

P0130, P0133

HO2S Bank 1 Sensor 2 Signal

P0137

P0140

P0138

P0139

HO2S Bank 2 Sensor 1 Signal

P0151

P0150, P0154

P0152

P0150, P0153

HO2S Bank 2 Sensor 2 Signal

P0157

P0160

P0158

P0159

Low Reference

--

P0130, P0150,

P0134, P0140, P0154, P0160

--

Circuit Description

The wide band heated oxygen sensor (HO2S) measures the amount of oxygen in the exhaust system and provides more information than the switching style HO2S. The wide band sensor consists of an oxygen sensing cell, an oxygen pumping cell, and a heater. The exhaust gas sample passes through a diffusion gap between the sensing cell and the pumping cell. The engine control module (ECM) supplies a voltage to the HO2S and uses this voltage as a reference to the amount of oxygen in the exhaust system. An electronic circuit within the ECM controls the pump current through the oxygen pumping cell in order to maintain a constant voltage in the oxygen sensing cell. The ECM monitors the voltage variation in the sensing cell and attempts to keep the voltage constant by increasing or decreasing the amount of current flow, or oxygen ion flow, to the pumping cell. By measuring the amount of current required to maintain the voltage in the sensing cell, the ECM can determine the concentration of oxygen in the exhaust. The HO2S voltage is displayed as a lambda value. A lambda value of 1 is equal to a stoichiometric air fuel ratio of 14.7:1. Under normal operating conditions, the lambda value will remain around 1. When the fuel system is lean, the oxygen level will be high and the lambda signal will be high or greater than 1. When the fuel system is rich, the oxygen level will be low, and the lambda signal will be low or less than 1. The ECM uses this information to maintain the correct air/fuel ratio. If the ECM detects that the HO2S signal voltage is low, this DTC sets.

Conditions for Running the DTC

    • The engine is operating.
    • The ignition 1 voltage is between 10.7-18 volts.
    • DTC P0130 and P0150 run continuously once the above conditions are met.

Conditions for Setting the DTC

The ECM detects that the HO2S signal voltage is out of range for greater than 4 seconds.

Action Taken when the DTCs Set

DTCs P0130 and P0150 are Type B DTCs.

Conditions for Clearing the MIL/DTC

DTCs P0130 and P0150 are Type B DTCs.

Diagnostic Aids

    •  The front wide band sensors do not toggle or switch like a switching HO2S. The front HO2S signals will be relatively stable for an idling engine.
    •  The following table illustrates the typical voltages for the HO2S circuits:

HO2S Voltages

HO2S Circuit

Voltage

    • Ignition ON, Engine OFF
    • HO2S Disconnected

Heater Control

4.6-5.0 V

Heater Supply Voltage

B+

Reference Voltage

2.6-3.1 V

Low Reference

2.2-2.7 V

Pump Current

2.5-3.0 V

Input Pump Current

2.5-3.0 V

Reference Information

Schematic Reference

Engine Controls Schematics

Connector End View Reference

Component Connector End Views

Electrical Information Reference

    •  Circuit Testing
    •  Connector Repairs
    •  Testing for Intermittent Conditions and Poor Connections
    •  Wiring Repairs

DTC Type Reference

Powertrain Diagnostic Trouble Code (DTC) Type Definitions

Scan Tool Reference

Control Module References for scan tool information

Circuit/System Verification

  1. Engine idling at normal operating temperature, verify the scan tool Loop Status Bn 1 Sen 1 and Loop Status Bn 2 Sen 1 parameters display Closed Loop.
  2. Operate the vehicle within the conditions for running the DTC to verify the DTC does not reset. You may also operate the vehicle within the conditions that are captured in the Freeze Frame/Failure Records Data List.

Circuit/System Testing

  1. Ignition OFF, disconnect the harness connector at the appropriate HO2S sensor.
  2. Ignition ON, test for 350-550 mV between the reference voltage circuit terminal 3 and the low reference circuit terminal 1.
  3. If less than the specified range, test the reference voltage circuit and the low reference circuit for a short to ground or an open/high resistance. If the circuits test normal, replace the ECM.
    If greater than the specified range, test the reference voltage circuit and the low reference circuit for a short to voltage. If the circuits test normal, replace the ECM.
  4. Test for 50-90 mV between the input pump current circuit terminal 4 and ground.
  5. If less than the specified range, test the input pump current circuit and the pump current circuit for a short to ground or an open/high resistance. If the circuits test normal, replace the ECM.
    If greater than the specified range, test the input pump current circuit and the pump current circuit for a short to voltage. If the circuits test normal, replace the ECM.
  6. If all circuits test normal, replace the HO2S sensor.

Repair Instructions

Perform the Diagnostic Repair Verification after completing the diagnostic procedure.

    •  Heated Oxygen Sensor Replacement - Bank 1 Sensor 1
    •  Heated Oxygen Sensor Replacement - Bank 1 Sensor 2
    •  Control Module References for engine control module replacement, setup, and programming