Application | Specification | |
|---|---|---|
Metric | English | |
Engine Performance | ||
Engine | 4-Cylinder/In-Line | |
Bore x Stroke | 87.5 x 100 mm | 3.44 x 3.94 in |
Displacement | 2,405 cm³ | 147 in³ |
Ignition Sequence | 1-3-4-2 | |
Compression Ratio | 9.6 : 1 | |
Maximum Power | T.B.D | |
Maximum Torque | T.B.D | |
Idle Speed Air Conditioning System (ON/OFF) | 690 RPM | |
Engine Part | ||
Ignition Type | Direct Ignition System (DIS) | |
Starter
| PG 260D (M/T, A/T) 1.4 kW (M/T, A/T) | |
Spark-Plug | ||
| FLR8LDCU (Bosch) | |
| 0.9-1.1 mm | 0.035-0.043 in |
Fuel Injection Type | MPI | |
Fuel Pump Type | Electric Motor Pump | |
Fuel Filter Type | Cartridge | |
Lubricating Type | Forced Feed Type | |
Oil Pump Type | Rotary (Trochoid) Pump | |
Cooling Type | Forced Water Circulation | |
Radiator Type | Cross - Flow | |
Water Pump Type | Centrifugal | |
Thermostat Type | Pellet Type | |
Battery
| MF 12V-60AH 650 | |
Generator
| AD 237 14.6±0.25 V - 120AH | |
Engine Oil | ||
| API SL (ILSAC GF-III) grade SAE 5W-30 * Hot area : SAE 10W-30 | |
| 4.5 L | 4.7 qt |
| 4.5 L | 4.75 qt |
| 4.3 L | 4.54 qt |
Coolant
| Dexcool | |
| 9 L | 9.51 qt |
Fuel Tank Capacity | 65 L | 17.2 gal |
General Data | ||
Engine Type | 4 Cylinder (In-Line) | |
Displacement | 2,405 cm³ | |
Bore Stroke | 87.5 X 100 mm | 3.44 X 3.94 in |
Compression Ratio | 9.6:1 | |
Firing Order | 1-3-4-2 | |
Maximum Power | hp | kw |
Maximum Torque | N·m | lb ft |
Cylinder Bore | ||
Diameter | 8.75485-87.505 mm | 3.444-3.445 in |
Out Of Round (MAX) | 0.013 mm | 0.0005 in |
Taper (MAX) | 0.013 mm | 0.0005 in |
Piston Protrusion | 0 mm | 0 in |
Oversize (Measure Replacement Piston Before Reboring | available in 0.50 mm (0.019 in) to suit bore | |
Block Face Distortion | 0.01 mm MAX | 0.00039 in |
Piston | ||
Diameter | 87.465-87.485 mm | 3.443-3.445 in |
Clearance To Bore | 0.010-0.030 mm | 0.00039-0.0020 in |
Ring Groove Width
| TBD | TBD |
Ring Groove Inner Diameter
| TBD | TBD |
Piston Rings | ||
Top Compression Ring End Gap | 0.3-0.5 mm | 0.011-0.019 in |
Second Compression Ring End Gap | 0.3-0.5 mm | 0.011-0.019 in |
Oil Ring End Gap | 0.4-1.4 mm | 0.0015-0.055 in |
Piston Ring With
| TBD | TBD |
Piston Ring Thickness
| TBD | TBD |
Ring Groove Clearance
| TBD | TBD |
Piston Pin | ||
Diameter | 20.9910-20.9970 mm | 0.82641-0.82665 in |
Pin Offset | 0.7-0.9 mm | 0.275-0.0354 in toward thrust side |
Clearance: In Piston | 0.011-0.014 mm | 0.00043-0.00055 in |
Clearance: In Rod | interference fit in rod | |
Length | 61.5 mm | 2.42 in |
Camshaft | ||
Valve Lift
| 9.2 mm 9.2 mm | 0.36 in 0.36 in |
Camshaft Cap To Bearing Journal Clearance | 0.04-0.144 mm | 0.0015-0.0056 in |
Bearing Journal OD | 42.455-43.470 mm | 1.6714-1.7114 in |
Crankshaft | ||
Main Journal - Diameter (All) | 57.982-57.995 mm | 2.2788-2.2833 in |
Main Journal - Radial Runout (Shaft Support On No. 1 And No. 5 Bearings Measured At No.3 Journal) | 0.03 mm | 0.00118 in |
Main Bearing Clearance (All) | 0.015-0.040 mm | 0.00059-0.00157 in |
End Play | 0.070-0.302 mm | 0.0027-0.0118 in |
Service Oversize (Available In 2 Sizes) | 0.25 and 0.5 mm | 0.00098 and 0.019 in |
Connecting Rod Journal | ||
Diameter (All) | 48.970-48.988 mm | 1.9279-1.9287 in |
Out Of Round (Max) | 0.004 mm | 0.00015 in |
Rod Bearing Play | 0.006-0.031 mm | 0.00023-0.00122 in |
Rod Bearing Clearance | 0.013~0.041 mm | 0.0005-0.0016 in |
Cylinder Head | ||
Valve Stem Protrusion | 39.2 mm MAX | 1.544 in |
Valve Guide Height | 13.7-14.0 mm | 0.53-0.55 in |
Overall Height | 133.975-134.025 mm | 5.2741-5.2759 in |
Minimum Overall Height After Machining | 133.9 mm | 5.271 in |
Valve System | ||
Valve Lash Compensators | Hydraulic | |
Seat Runout (MAX, All) | 0.03 mm | 0.0018 in |
Face Runout (MAX, All) | 0.03 mm | 0.0018 in |
Valve Diameter
| 32±0.1 mm 29± 0.1 mm | 1.2598± 0.0039 in 1.1417±0.00039 in |
Valve Stem Diameter
| 5.955-5.970 mm 5.945-5.960 mm | 0.234-0.235 in 0.2346-0.2360 in |
Valve Seat Width
| 1.0-1.5 mm 1.7-2. mm | 0.039-0.059 in 0.066-0.086 in |
Valve Face Angle | 44° | |
Valve Seat Angle | 45° | |
Valve Guide Inside Diameter | 6.000-6.012 mm | 0.2362-0.2367 in |
Oil Pump | ||
Type | Rotary (Trochoild) | |
Gear Lash | 0.10-0.20 mm | 0.0040-0.008 in |
Outer Gear to Body | 0.11-0.19 mm | 0.0043-0.0074 in |
Outer Gear to Crescent | 0.11-0.24 mm | 0.0043-0.009 in |
Inner Gear to Crescent | 0.18-0.26 mm | 0.007-0.010 in |
End Clearance | 0.03-0.10 mm | 0.001-0.004 in |
