Scan Tool Does Not Communicate with Low Speed GMLAN Device. Holden Barina 2009

For 1990-2009 cars only

Makes 🢒 Holden 🢒 2009 🢒 Barina 🢒 Power and Signal Distribution 🢒 Data Communications 🢒 Scan Tool Does Not Communicate with Low Speed GMLAN Device

Diagnostic Instructions

•	Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure.

•	Review Strategy Based Diagnosis for an overview of the diagnostic approach.

•	Diagnostic Procedure Instructions provides an overview of each diagnostic category.

Diagnostic Fault Information

Circuit	Short to Ground	Open/High Resistance	Short to Voltage	Signal Performance
Low Speed GMLAN Serial Data	1	U0100-U0299	1	--
Ground (DLC, terminal 5)	--	1	--	--
1. No communication on any low speed GMLAN module

The serial data is transmitted over a single wire to the appropriate control modules. The transmission speed for GMLAN low speed is up to 83.33 Kb/s. Under normal vehicle operating conditions, the speed of the buss is 33.33 Kb/s. The control modules toggle the serial data circuit between 0-5 V during normal communications. To wake the control modules connected to the GMLAN low speed serial data circuit, a voltage wake up pulse of 10 V is sent out. If serial data is lost, control modules will set a no communication code against the non-communicating control module. Note: a loss of serial data communications DTC does not represent a failure of the module that set it.

Diagnostic Aids

•

Sometimes, while diagnosing a specific customer concern or after a repair, you may notice a history U-code present. However, there is no associated "current" or "active" status. Loss-of- communication U-codes such as these can set for a variety of reasons. Many times, they’re transparent to the vehicle operator and technician, and/or have no associated symptoms. Eventually, they will erase themselves automatically after a number of fault-free ignition cycles. This condition would most likely be attributed to one of these scenarios:

-	A control module on the data communication circuit was disconnected while the communication circuit is awake.

-	Power to one or more modules was interrupted during diagnosis

-	A low battery condition was present, so some control modules stop communicating when battery voltage drops below a certain threshold.

-	Battery power was restored to the vehicle and control modules on the communication circuit did not all re-initialize at the same time.

-	If a loss-of-communication U-code appears in history for no apparent reason, it is most likely associated with one of the scenarios above. These are all temporary conditions and should never be interpreted as an intermittent fault, causing you to replace a part.

•	Do not replace a control module reporting a U-code. The U-code identifies which control module needs to be diagnosed for a communication issue.

•	Communication may be available between the IPC and the scan tool with the low speed GMLAN serial data system inoperative. This condition is due to the IPC using both the high and low speed GMLAN systems.

•	An open in the DLC ground circuit terminal 5 will allow the scan tool to operate but not communicate with the vehicle. When the scan tool attempts to communicate with the vehicle a No CANdi Module Detected message will be displayed.

•	The engine will not start when there is a total malfunction of the low speed GMLAN serial data circuit.

Reference Information

Electrical Information Reference

•	Circuit Testing

•	Connector Repairs

•	Testing for Intermittent Conditions and Poor Connections

•	Wiring Repairs

Circuit/System Testing

Note: Use the schematic to identify the following:

•	Control modules the vehicle is equipped with

•	Control module locations on the low speed serial data circuit

•	Each control modules low speed serial data circuit terminals

Attempt to communicate with all control modules on the low speed GMLAN serial data circuit, refer to Data Link References. Communications should not be available with two or more control modules on the low speed GMLAN serial data circuit.

⇒	If only one control module is not communicating, diagnose that control module only, refer to DTC U0100-U0299.

⇒	If one or more control modules are communicating but not all, refer to Testing the Serial Data Circuit for an Open/High Resistance.

Disconnect the scan tool from the DLC. The following tests will be done at the DLC connector.
All access doors closed, ignition OFF for 60 seconds, test for less than 10 Ω between the ground circuit terminal 5 and ground.

⇒	If greater than the specified range, test the ground circuit for an open/high resistance.

Ignition ON, test for less than 4.5 V between the serial data circuit terminal 1 and ground.

⇒	If greater than the specified range, test the serial data circuit for a short to voltage, refer to Testing the Serial Data Circuit for a Short to Voltage.

Ignition OFF for 60 seconds, test for greater than 100 Ω between the serial data circuit terminal 1 and ground.

⇒	If less than the specified range, test the serial data circuit for a short to ground, refer to Testing the Serial Data Circuits for a Short to ground.

Testing the Serial Data Circuits for a Short to Voltage

Ignition OFF, disconnect the harness connector at the low speed GMLAN serial data circuit splice pack.
Ignition ON, test for less than 4.5 V between the DLC serial data circuit terminal 1 and ground.

⇒	If greater than the specified range, repair the short to voltage.

Test for less than 4.5 V between each serial data circuit at the splice pack connector and ground.

⇒	If greater than the specified range, perform the appropriate test listed below:

•	Serial data circuits with one control module, test the serial data circuit for a short to voltage. If the circuit tests normal replace the control module.

•	Serial data circuits with 2 or more control modules, test each section of the serial data circuit for a short to voltage. If the circuits test normal, replace the control module that causes the short to voltage when connected.

Testing the Serial Data Circuits for a Short to Ground

Ignition OFF, disconnect the harness connector at the low speed GMLAN serial data circuit splice pack..
Test for infinite resistance between the DLC serial data circuit terminal 1 and ground.

⇒	If not the specified value, repair the short to ground.

Ignition OFF for 60 seconds, test for greater than 100 Ω between each serial data circuit and ground.

⇒	If less than the specified range, perform the appropriate test listed below:

•	Serial data circuits with one control module, test the serial data circuit for a short to ground. If the circuit tests normal replace the control module.

•	Serial data circuits with 2 or more control modules, test each section of the serial data circuit for a short to ground. If the circuits test normal, replace the control module that causes the short to ground when connected.

Testing the Serial Data Circuit for an Open/High Resistance

Ignition OFF, disconnect the harness connector at the low speed GMLAN serial data circuit splice pack.
Install a 3 A fused jumper wire between the disconnected splice pack connector DLC terminal and a low speed GMLAN serial data circuit terminal that is not communicating.
Ignition ON, verify the scan tool communicates with the control modules connected to the low speed GMLAN serial data circuit.

⇒	If any control module does not communicate, test each section of the serial data circuit for an open/high resistance. If the circuits test normal, replace the control module that does not communicate when connected.

Repair Instructions

Perform the Diagnostic Repair Verification after completing the repair.

•	GMLAN Wiring Repairs

•	Control Module References for module replacement, setup, and programming