The front fog lamp relay is supplied with battery voltage at all times. The front fog lamp switch signal circuit is grounded momentarily by pressing the front fog lamp switch. The body control module (BCM) energizes the front fog lamp relay by applying ground to the front fog lamp relay control circuit. When the front fog lamp relay is energized, the relay switch contacts close and battery voltage is applied through the FOG LAMP fuse to the front fog lamp supply voltage circuit which illuminates the front fog lamps.

Schematic Reference

Fog Lights Schematics

Connector End View Reference

Component Connector End Views

Description and Operation

Exterior Lighting Systems Description and Operation

Electrical Information Reference

Scan Tool Reference

Control Module References for scan tool information

1. Ignition ON, observe the scan tool Front Fog Lamp Switch parameter while pressing and releasing the front fog lamp switch. The reading should change between Active and Inactive.

⇒	If not the specified value, refer to the Front Fog Lamp Switch Malfunction.

2. Ignition ON, command the Fog Lamps ON and OFF with a scan tool. Verify the front fog lamps turn ON and OFF.

⇒	If the front fog lamps do not turn ON and OFF, refer to the Front Fog Lamp Malfunction.

Front Fog Lamp Switch Malfunction

1. Ignition OFF, disconnect the X1 harness connector at the headlamp and panel dimmer switch.
2. Ignition OFF, verify a test lamp illuminates between B+ and the ground circuit terminal 8.

⇒	If the test lamp does not illuminate, test the ground circuit for an open/high resistance.

3. Ignition ON, verify the scan tool front fog lamp switch parameter is INACTIVE.

⇒	If not the specified value, test the signal circuit terminal 10 for a short to ground. If the circuit tests normal, replace the BCM.

4. Install a 3A fused jumper wire between the signal circuit terminal 10 and the ground circuit terminal 8. Verify the scan tool front fog lamp switch parameter is ACTIVE.

⇒	If not the specified value, test the signal circuit for a short to voltage or an open/high resistance. If the circuit tests normal, replace the BCM.

5. If all circuits test normal, test or replace the headlamp and panel dimmer switch.

Front Fog Lamps Malfunction

1. Ignition OFF, disconnect the front fog lamp relay.
2. Ignition ON, verify a test lamp does not illuminate between the control circuit terminal 87 and ground.

⇒	If the test lamp illuminates, test the control circuit for a short to voltage.

3. Verify a test lamp illuminates between the B+ circuit terminal 30 and ground.

⇒	If the test lamp does not illuminate, test the B+ circuit for a short to ground or an open/high resistance.

4. Verify a test lamp illuminates between the B+ circuit terminal 85 and ground.

⇒	If the test lamp does not illuminate, test the B+ circuit for an open/high resistance.

5. Disconnect the harness connector at the inoperative front fog lamp.
6. Ignition OFF, test for less than 5.0 ohms between the ground circuit terminal B and ground.

⇒	If greater than the specified range, test the ground circuit for an open/high resistance.

7. Connect the harness connector at the inoperative front fog lamp.
8. Connect a 15A fused jumper wire between the B+ circuit terminal 30 and the control circuit terminal 87. Verify the front fog lamps are activated.

⇒	If the front fog lamps do not activate, test the control circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the inoperative front fog lamp.

9. Connect a test lamp between the B+ circuit terminal 85 and the control circuit terminal 86.
10. Ignition ON, command the front fog lamps ON and OFF with a scan tool. The test lamp should turn ON and OFF when changing between the commanded states.

⇒	If the test lamp is always ON, test the control circuit for a short to ground. If the circuit tests normal, replace the BCM.

⇒	If the test lamp is always OFF, test the control circuit for a short to voltage or open/high resistance. If the circuit tests normal, replace the BCM.

11. If all circuits test normal, test or replace the front fog lamp relay.

Perform the Diagnostic Repair Verification after completing the diagnostic procedure.