GM Service Manual Online
For 1990-2009 cars only

Circuit Description

Heated oxygen sensors (HO2S) are used for fuel control and post catalyst monitoring. Each HO2S compares the oxygen content of the surrounding air with the oxygen content in the exhaust stream. The HO2S must reach operating temperature to provide an accurate voltage signal. Heating elements inside the HO2S minimize the time required for the sensors to reach operating temperature. The powertrain control module (PCM) supplies the HO2S with a reference, or bias, voltage of about 450 mV. When the engine is first started the PCM operates in open loop, ignoring the HO2S voltage signal. Once the HO2S reaches operating temperature and closed loop is achieved, the HO2S generates a voltage within a range of 0-1,000 mV that fluctuates above and below bias voltage. High HO2S voltage indicates a rich exhaust stream; low HO2S voltage indicates a lean exhaust stream. This diagnostic will only run once per ignition cycle. The PCM monitors the rich-to-lean and lean-to-rich transition time. A transition is defined as, the HO2S voltage changes from greater than 625 mV to less than 250 mV or from less than 250 mV to greater than 625 mV. If the PCM detects that the difference between the rich-to-lean average transition time and lean-to-rich average transition time is greater than a specified value, DTC P1134 sets for HO2S bank 1 sensor 1, or DTC P1154 sets for HO2S bank 2 sensor 1.

DTC Descriptors

This diagnostic procedure supports the following DTCs:

    • DTC P1134 HO2S Transition Time Ratio Bank 1 Sensor 1
    • DTC P1154 HO2S Transition Time Ratio Bank 2 Sensor 1

Conditions for Running the DTC

    • DTCs P0068, P0101, P0102, P0103, P0106, P0107, P0108, P0112, P0113, P0116, P0117, P0118, P0120, P0128, P0131, P0132, P0134, P0135, P0151, P0152, P0154, P0155, P0169, P0178, P0179, P0200, P0220, P0442, P0446, P0452, P0453, P0455, P0496, P1125, P1258, P1516, P2101, P2108, P2135, U0107 are not set.
    • The ECT Sensor parameter is more than 60°C (140°F).
    • The EVAP Purge Solenoid Command parameter is more than 1 percent.
    • The MAF Sensor parameter is between 20-55 g/s.
    • The Engine Speed parameter is between 1,200-3,000 RPM.
    • The TP Indicated Angle parameter is 5 percent more than the value observed at idle.
    • The Loop Status parameter is closed.
    • The Ignition 1 Signal parameter is between 10-18 volts.
    • The Fuel Alcohol content parameter is less than 90 percent.
    • The Fuel Tank Level Remaining parameter is more than 10 percent.
    • The Engine Run Time parameter is more than 160 seconds.
    • The above conditions are met for 1 second.
    • This diagnostic runs one time per drive cycle once the above conditions are met.

Conditions for Setting the DTC

The PCM detects that the difference between the HO2S rich-to-lean average transition time and the lean-to-rich average transition time is more than a calibrated value for 100 seconds.

Action Taken When the DTC Sets

    • The control module illuminates the malfunction indicator lamp (MIL) on the second consecutive ignition cycle that the diagnostic runs and fails.
    • The control module records the operating conditions at the time the diagnostic fails. The first time the diagnostic fails, the control module stores this information in the Failure Records. If the diagnostic reports a failure on the second consecutive ignition cycle, the control module records the operating conditions at the time of the failure. The control module writes the operating conditions to the Freeze Frame and updates the Failure Records.

Conditions for Clearing the MIL/DTC

    • The control module turns OFF the malfunction indicator lamp (MIL) after 3 consecutive ignition cycles that the diagnostic runs and does not fail.
    • A current DTC, Last Test Failed, clears when the diagnostic runs and passes.
    • A history DTC clears after 40 consecutive warm-up cycles, if no failures are reported by this or any other emission related diagnostic.
    • Clear the MIL and the DTC with a scan tool.

Test Description

The number below refers to the step number on the diagnostic table.

  1. If the voltage is varying above and below the specified value, the condition is not present.

Step

Action

Value(s)

Yes

No

Schematic Reference: Engine Controls Schematics

Connector End View Reference: Engine Controls Connector End Views or Powertrain Control Module Connector End Views

1

Did you perform the Diagnostic System Check - Vehicle?

--

Go to Step 2

Go to Diagnostic System Check - Vehicle

2

  1. Start the engine.
  2. Allow the engine to reach operating temperature. Refer to Scan Tool Data List .
  3. Operate the engine at 1,500 RPM for 30 seconds.
  4. Observe the affected heated oxygen sensor (HO2S) voltage parameter with a scan tool.

Is the HO2S voltage parameter varying above and below the specified range?

250-625 mV

Go to Step 3

Go to Step 4

3

  1. Observe the Freeze Frame/Failure Records for this DTC.
  2. Turn OFF the ignition for 30 seconds.
  3. Start the engine.
  4. Operate the vehicle within the Conditions for Running the DTC. You may also operate the vehicle within the conditions that you observed from the Freeze Frame/Failure Records.

Did the DTC fail this ignition?

--

Go to Step 4

Go to Testing for Intermittent Conditions and Poor Connections

4

  1. Turn OFF the ignition.
  2. Disconnect the affected HO2S.
  3. Connect a 3-amp fused jumper wire between the high signal circuit of the HO2S harness connector on the engine harness side and a good ground.
  4. Turn ON the ignition, with the engine OFF.
  5. Observe the HO2S voltage parameter with a scan tool.

Is the HO2S voltage parameter less than the specified value?

100 mV

Go to Step 6

Go to Step 5

5

Test the HO2S high signal circuit for an open or high resistance. Refer to the following procedures:

    •  Circuit Testing
    •  Wiring Repairs

Did you find and correct the condition?

--

Go to Step 12

Go to Step 9

6

  1. Remove the jumper wire from the previous step.
  2. Connect a 3-amp fused jumper wire between the high signal circuit of the HO2S harness connector on the engine harness side and the low signal circuit of the HO2S harness connector on the engine harness side.
  3. Observe the HO2S voltage parameter with a scan tool.

Is the HO2S voltage parameter less than the specified value?

100 mV

Go to Step 8

Go to Step 7

7

Test the HO2S low signal circuit for an open or high resistance. Refer to the following procedures:

    •  Circuit Testing
    •  Wiring Repairs

Did you find and correct the condition?

--

Go to Step 12

Go to Step 9

8

Test for shorted terminals and for poor connections at the HO2S. Refer to the following procedures:

    •  Connector Repairs

Did you find and correct the condition?

--

Go to Step 12

Go to Step 10

9

Test for shorted terminals and for poor connections at the powertrain control module (PCM). Refer to the following procedures:

    •  Connector Repairs

Did you find and correct the condition?

--

Go to Step 12

Go to Step 11

10

Notice: Refer to Silicon Contamination of Heated Oxygen Sensors Notice in the Preface section.

Important: The HO2S may be damaged due to contamination. Prior to replacing the HO2S inspect for the following sources of contamination:

    • A silicon contaminated HO2S
    • Fuel contamination--Refer to Alcohol/Contaminants-in-Fuel Diagnosis .
    • Engine oil consumption--Refer to Oil Consumption Diagnosis .
    • Engine coolant consumption--Refer to Loss of Coolant .

Replace the affected HO2S. Refer to Heated Oxygen Sensor Replacement - Bank 1 Sensor 1 or Heated Oxygen Sensor Replacement - Bank 2 Sensor 1 .

Did you complete the replacement?

--

Go to Step 12

--

11

Replace the PCM. Refer to Control Module References for replacement, setup, and programming.

Did you complete the replacement?

--

Go to Step 12

--

12

  1. Clear the DTCs with a scan tool.
  2. Turn OFF the ignition for 30 seconds.
  3. Start the engine.
  4. Operate the vehicle within the Conditions for Running the DTC. You may also operate the vehicle within the conditions that you observed from the Freeze Frame/Failure Records.

Did the DTC fail this ignition?

--

Go to Step 2

Go to Step 13

13

Observe the Capture Info with a scan tool.

Are there any DTCs that have not been diagnosed?

--

Go to Diagnostic Trouble Code (DTC) List - Vehicle

System OK