GM Service Manual Online
For 1990-2009 cars only

Circuit Description

The rear HVAC control module monitors the air temperature in the upper auxiliary discharge duct via a temperature sensor. When the air is cold, the sensor resistance and signal voltage are high. When the air is warm, the sensor resistance and signal voltage are low. The rear auxiliary HVAC control module converts this voltage to a digital signal that can be transmitted over the keyboard display driver (KDD) data bus to the HVAC control module. The HVAC control module contains the logic that controls the auxiliary air temperature and is responsible for setting the DTC.

Conditions for Running the DTC

The ignition is turned ON.

Conditions for Setting the DTC

The HVAC control module detects the signal circuit is less than 0.09 V (5 counts) or greater than 4.90 V (250 counts).

Action Taken When the DTC Sets

A default value of 2.50 V (127 counts) will be used for the sensor data by the HVAC control module. The sensor reading displayed on the scan tool in the HVAC data list will be this default value.

Conditions for Clearing the DTC

    • The DTC will become history if the HVAC Control Module no longer detects a failure.
    • The history DTC will clear after 50 fault free ignition cycles.
    • The DTC can be cleared with a scan tool.

Diagnostic Aids

Check the following conditions:

    • Visually inspect the sensor for contamination or damage.
    • Verify that air flow to sensor is not restricted.
    • Verify that the sensor is installed properly.
    • Refer to Testing for Intermittent Conditions and Poor Connections in Wiring Systems.

Test Description

The number(s) below refer to the step number(s) on the diagnostic table.

  1. Tests for the possibility of a short to another 5 V reference circuit.

Step

Action

Value(s)

Yes

No

Schematic Reference: HVAC Air Delivery/Temperature Control Schematics

1

Did you perform the HVAC Diagnostic System Check?

--

Go to Step 2

Go to Diagnostic System Check

2

  1. Turn OFF the ignition.
  2. Disconnect the rear a/c temperature sensor.
  3. Turn ON the ignition, with the engine OFF.
  4. Measure the voltage from the rear a/c temperature sensor signal circuit of the rear a/c temperature sensor to a good ground.

Does the voltage measure near the specified value?

5 V

Go to Step 3

Go to Step 4

3

Measure the voltage from the rear a/c temperature sensor signal circuit to the low reference circuit of the rear a/c temperature sensor.

Does the voltage measure near the specified value?

5 V

Go to Step 6

Go to Step 5

4

Test the rear a/c temperature sensor signal circuit of the rear a/c temperature sensor for an open, high resistance, short to ground, or short to voltage. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

--

Go to Step 12

Go to Step 9

5

Test the low reference circuit of the rear a/c temperature sensor for a high resistance or an open. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

--

Go to Step 12

--

6

Inspect for poor connections at the harness connector of the rear a/c temperature sensor. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.

Did you find and correct the condition?

--

Go to Step 12

Go to Step 7

7

Test the rear a/c temperature sensor resistance. Refer to the Sensor Resistance Table .

Does the resistance measure near the Sensor Resistance Table value?

--

Go to Step 8

Go to Step 10

8

  1. Disconnect the rear HVAC control module.
  2. Turn ON the ignition, with the engine OFF.
  3. Test the rear a/c temperature sensor signal circuit of the rear a/c temperature sensor for a short to voltage. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

--

Go to Step 12

Go to Step 9

9

Inspect for poor connections at the harness connector of the rear HVAC control module. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.

Did you find and correct the condition?

--

Go to Step 12

Go to Step 11

10

Replace the rear a/c temperature sensor. Refer to Air Conditioning (A/C) Temperature Sensor Replacement .

Did you complete the replacement?

--

Go to Step 12

--

11

Important:: Perform the set up procedure for the rear HVAC control module.

Replace the rear HVAC control module. Refer to Control Assembly Replacement - Auxiliary .

Did you complete the replacement?

--

Go to Step 12

--

12

  1. Use the scan tool in order to clear the DTCs.
  2. Operate the vehicle within the Conditions for Running the DTC as specified in the supporting text.

Does the DTC reset?

--

Go to Step 2

System OK