GM Service Manual Online
For 1990-2009 cars only

Front Drive Axle Inner Shaft and Inner Shaft Housing Replacement 8.25 F4WD Axle

Removal Procedure

  1. Raise the vehicle. Refer to Lifting and Jacking the Vehicle .
  2. Drain the differential carrier assembly. Refer to Front Axle Lubricant Replacement .
  3. If only replacing the right side inner shaft and/or housing, follow the steps below. If only replacing the left side inner shaft, proceed to step 13.
  4. Remove the stabilizer shaft link assembly. Refer to Stabilizer Shaft Link Replacement .

  5. Object Number: 763646  Size: SH
  6. Remove the wheel drive shaft inboard flange bolts from the inner axle shaft.
  7. Disconnect the wheel drive shaft from the inner axle shaft.

  8. Object Number: 763648  Size: SH
  9. Disconnect the inner axle shaft from the differential case side gear using a hammer and brass drift.

  10. Object Number: 763653  Size: SH
  11. Remove the inner axle shaft housing nuts from the bracket.

  12. Object Number: 763644  Size: SH
  13. Remove the inner axle shaft housing bolts from the differential carrier assembly.
  14. Remove the inner axle shaft and inner axle shaft housing from the vehicle.
  15. Remove the inner axle shaft from the inner axle shaft housing.
  16. Remove the inner axle shaft seal and the bearing from the inner axle shaft housing. Refer to Front Drive Axle Inner Shaft Seal and Inner Shaft Bearing Replacement .

  17. Object Number: 1581720  Size: SH
  18. If only replacing the left side inner axle shaft, perform the following steps:
  19. 13.1. Remove the wheel drive shaft inboard flange bolts from the inner axle shaft.

    Disconnect the wheel drive shaft from the inner axle shaft.

    13.2. Remove the inner axle shaft using a hammer and a brass drift.

Installation Procedure


    Object Number: 1581721  Size: SH
  1. If only the left side inner axle shaft was removed, install the shaft by performing the following steps:
  2. 1.1. Install the inner axle shaft into the differential case side gear using a soft-faced mallet until the retaining ring on the inner axle shaft is fully seated within the groove in the differential case side gear. Pull back on the inner axle shaft to ensure that the inner axle shaft is properly retained in the differential case side gear.
    1.2. Connect the wheel drive shaft to the inner axle shaft.

    Notice: Refer to Fastener Notice in the Preface section.

    1.3. Install the wheel drive shaft inboard flange to inner axle shaft bolts.

    Tighten
    Tighten the wheel drive shaft inboard flange to inner axle shaft bolts to 79 N·m  (58 lb ft).

  3. If the right side inner axle shaft and/or housing was removed, install the shaft and/or housing following the steps below.
  4. Install the new inner axle shaft bearing and the new seal to the inner axle shaft housing. Refer to Front Drive Axle Inner Shaft Seal and Inner Shaft Bearing Replacement .
  5. Install the inner axle shaft into the inner axle shaft housing.
  6. Do not install the inner axle shaft completely into the inner axle shaft housing at this time.

  7. Apply sealant to the inner axle housing to differential carrier sealing surface. Use the correct sealant. Refer to Adhesives, Fluids, Lubricants, and Sealers .
  8. Install the inner axle shaft and the inner axle shaft housing to the differential carrier assembly.

  9. Object Number: 763644  Size: SH
  10. Install the inner axle shaft housing bolts.
  11. Tighten
    Tighten the inner axle shaft housing bolts to 40 N·m  (30 lb ft).


    Object Number: 763653  Size: SH
  12. Install the inner axle shaft housing nuts to the bracket.
  13. Tighten
    Tighten the inner axle shaft housing nuts to 100 N·m (75 lb ft).

  14. Install the inner axle shaft into the differential case side gear by doing the following:
  15. 9.1. Turn the inner axle shaft and align the splines of the inner axle shaft with the splines on the differential side gear.
    9.2. Install the inner axle shaft into the differential case side gear using a soft-faced mallet until the retaining ring on the inner axle shaft is fully seated within the groove in the differential case side gear.
    9.3. Pull back on the inner axle shaft to ensure that the inner axle shaft is properly retained in the differential case side gear.
  16. Install the wheel drive shaft inboard flange to the inner axle shaft.

  17. Object Number: 763646  Size: SH
  18. Install the wheel drive shaft inboard flange to inner axle shaft bolts.
  19. Tighten
    Tighten the wheel drive shaft inboard flange to inner axle shaft bolts to 79N·m  (58 lb ft).

  20. Install the stabilizer shaft link assembly. Refer to Stabilizer Shaft Link Replacement .
  21. With either replacement procedure, fill the differential carrier assembly with axle lubricant. Use the correct fluid. Refer to Front Axle Lubricant Replacement .
  22. Lower the vehicle.

Front Drive Axle Inner Shaft and Inner Shaft Housing Replacement 8.25 S4WD and 9.25 Axles

Removal Procedure


    Object Number: 834234  Size: SH
  1. Raise the vehicle. Refer to Lifting and Jacking the Vehicle .
  2. Drain the differential carrier assembly. Refer to Front Axle Lubricant Replacement .
  3. If only replacing the right side inner shaft and/or housing, follow the steps below. If only replacing the left side inner shaft, proceed to step 16.
  4. Remove the stabilizer shaft link assembly. Refer to Stabilizer Shaft Link Replacement .
  5. Disconnect the electrical connector from the electric motor actuator.

  6. Object Number: 834265  Size: SH
  7. Disconnect the wire harness from the inner axle shaft housing.

  8. Object Number: 763646  Size: SH
  9. Remove the wheel drive shaft inboard flange bolts from the inner axle shaft.
  10. Disconnect the wheel drive shaft from the inner axle shaft.


    Object Number: 834241  Size: SH
  11. Remove the inner axle shaft housing nuts from the bracket.

  12. Object Number: 365933  Size: SH
  13. For 25/35 series vehicles, perform the following steps in order to provide additional clearance so the inner axle housing can be removed from the vehicle:
  14. 9.1. Remove the front axle mounting bracket to frame nuts.
    9.2. Slide the front axle mounting bracket towards the engine. It may be necessary to pull down on the inner axle housing and/or push up on the mounting bracket in order to gain clearance.

    Object Number: 834261  Size: SH
  15. Remove the inner axle shaft housing bolts from the differential carrier case.

  16. Object Number: 615922  Size: SH

    Important: Keep the open end of the inner axle shaft housing up.

  17. Carefully remove the inner axle shaft housing assembly from the differential carrier assembly.

  18. Object Number: 892812  Size: SH
  19. Remove the following components from the inner axle shaft housing:
  20. 12.1. The clutch fork inner spring (10)
    12.2. The clutch fork assembly (11)
    12.3. The clutch shaft shim (9)
    12.4. The clutch sleeve (8)
    12.5. The retainer ring (7)
    12.6. The thrust washers (5, 6)

    Object Number: 615683  Size: SH
  21. Remove the inner axle shaft (2). Tap out the inner axle shaft with a soft-faced mallet, if necessary.
  22. Remove the inner axle seal and the bearing from the axle housing. Refer to Front Drive Axle Inner Shaft Seal and Inner Shaft Bearing Replacement .

  23. Object Number: 1581720  Size: SH
  24. If only replacing the left side inner axle shaft, perform the following steps:
  25. 15.1. Remove the wheel drive shaft inboard flange bolts from the inner axle shaft.

    Disconnect the wheel drive shaft from the inner axle shaft.

    15.2. Remove the inner axle shaft using a hammer and a brass drift.

Installation Procedure


    Object Number: 1581721  Size: SH
  1. If only the left side inner axle shaft was removed, install the shaft by performing the following steps:
  2. 1.1. Install the inner axle shaft into the differential case side gear using a soft-faced mallet until the retaining ring on the inner axle shaft is fully seated within the groove in the differential case side gear. Pull back on the inner axle shaft to ensure that the inner axle shaft is properly retained in the differential case side gear.
    1.2. Connect the wheel drive shaft to the inner axle shaft.

    Notice: Refer to Fastener Notice in the Preface section.

    1.3. Install the wheel drive shaft inboard flange to inner axle shaft bolts.

    Tighten
    Tighten the wheel drive shaft inboard flange to inner axle shaft bolts to 79 N·m  (58 lb ft).

  3. If the right side inner axle shaft and/or housing was removed, install the shaft and/or housing following the steps below.
  4. Install the new inner axle shaft bearing and the seal to the axle housing. Refer to Front Drive Axle Inner Shaft Seal and Inner Shaft Bearing Replacement .

  5. Object Number: 615683  Size: SH
  6. Install the inner axle shaft (2) into the inner axle shaft housing (1).
  7. Carefully tap the inner axle shaft into place with a soft-faced mallet.

  8. Place the inner axle shaft housing on end so that the splines of the inner axle shaft is facing up.

  9. Object Number: 892812  Size: SH
  10. Install the following components into the inner axle shaft housing:
  11.         Important: Use chassis grease in order to hold the thrust washer in place.

    6.1. The thrust washer (5)

    Ensure the tabs on the thrust washer are aligned with the slots in the inner axle shaft housing (4).

    6.2. The second thrust washer (6)
    6.3. The retainer ring (7) onto the inner axle shaft (1).
    6.4. Determine the clutch gear shim thickness. Refer to Inner Axle Shaft Shim Adjustment .
    6.5. The clutch gear shim (9)
    6.6. The clutch sleeve (8)
    6.7. The clutch fork assembly (11)
    6.8. The clutch fork inner spring (10)
  12. Apply sealant to the inner axle housing to differential carrier sealing surface. Use the correct sealant. Refer to Adhesives, Fluids, Lubricants, and Sealers .

  13. Object Number: 893259  Size: SH
  14. Install the inner axle shaft housing assembly to the differential carrier assembly.

  15. Object Number: 834261  Size: SH
  16. Install the inner axle shaft housing bolts.
  17. Tighten
    Tighten the inner axle shaft housing bolts to 40 N·m  (30 lb ft).


    Object Number: 365933  Size: SH
  18. For 25/35 series vehicles, perform the following steps in order to install the front axle mounting bracket to the inner axle shaft housing:
  19. 10.1. Slide the front axle mounting bracket towards the frame.

    Install the front axle mounting bracket studs into the inner shaft housing mounting flange.

    It may be necessary to push up on the front axle mounting bracket and/or pull down on the inner axle housing in order to gain enough clearance to install the mounting bracket studs into the inner shaft housing.

    10.2. Install the front axle mounting bracket to frame nuts.

    Tighten
    Tighten the inner axle shaft housing mounting bracket to frame nuts to 90 N·m (67 lb ft).


    Object Number: 834241  Size: SH
  20. Install the inner axle shaft housing washers and nuts to the bracket.
  21. Tighten
    Tighten the inner axle shaft housing nuts to 100 N·m (75 lb ft).

  22. Connect the wheel drive shaft inboard flange to the inner axle shaft.

  23. Object Number: 763646  Size: SH
  24. Install the wheel drive shaft inboard flange to the inner axle shaft bolts.
  25. Tighten
    Tighten the wheel drive shaft inboard flange to inner axle shaft bolts to 79 N·m  (58 lb ft).


    Object Number: 834265  Size: SH
  26. Connect the wire harness to the inner axle shaft housing.

  27. Object Number: 834234  Size: SH
  28. Connect the electrical connector to the front axle actuator.
  29. Install the stabilizer shaft link assembly. Refer to Stabilizer Shaft Link Replacement .
  30. With either replacement procedure, fill the differential carrier assembly with axle lubricant. Use the correct fluid. Refer to Front Axle Lubricant Replacement .
  31. Lower the vehicle.