GM Service Manual Online
For 1990-2009 cars only

Circuit Description

The inflatable restraint IP module deployment loop consists of an IP module, IP module high control circuit, and IP module low control circuit. A shorting bar is used on the IP module connector which will short together the IP module high and IP module low control circuits when the connector is disconnected. This will help to prevent unwanted deployment of the inflator module during servicing. When the ignition is turned ON, the inflatable restraint sensing and diagnostic module (SDM) performs continuous diagnostic tests on the deployment loops to check for proper circuit continuity and for shorts to ground or voltage. If a malfunction is detected, a DTC will be stored.

Conditions for Running the DTC

Ignition 1 voltage is within the normal operating voltage range.

Conditions for Setting the DTC

The SDM detects the IP module deployment loop resistance is less than 1.3 ohms for 500 milliseconds.

Action Taken When the DTC Sets

The SDM commands ON the AIR BAG indicator via Class 2 serial data.

Conditions for Clearing the DTC

    • The condition responsible for setting the DTC no longer exists.
    • You issue a scan tool CLEAR DTCs command.
    • A history DTC will clear once 255 malfunction free ignition cycles have occurred.

Diagnostic Aids

The following can cause an intermittent condition:

    • A short between the IP module high and IP module low control circuits
    • A malfunctioning shorting bar on the IP module connector

Refer to Testing for Intermittent Conditions and Poor Connections in Wiring Systems.

Test Description

The numbers below refer to the step numbers on the diagnostic table.

  1. This step inspects the IP module in-line connector.

  2. Tests for a malfunctioning IP module.

  3. Tests for a short between the IP module high and IP module low control circuits.

Step

Action

Yes

No

Schematic Reference: SIR Schematics

1

Did you perform A Diagnostic System Check - SIR?

Go to Step 2

Go to Diagnostic System Check - SIR

2

  1. Turn OFF the ignition.
  2. Disconnect the IP module in-line connector. Refer to Inflatable Restraint Instrument Panel Module Replacement .
  3. Inspect both halves of the connector for the following conditions:
  4. • Corrosion
    • Terminal damage
    • Poor connections/terminal tension

Do the connectors exhibit any signs of corrosion, terminal damage, or poor connections?

Go to Step 3

Go to Step 4

3

  1. Replace the harness side of the in-line connector. Refer to Connector Repairs in Wiring Systems.
  2. If the IP module connector exhibits any of the above conditions, the module must be replaced. Refer to Inflatable Restraint Instrument Panel Module Replacement .

Did you complete the replacement?

Go to Step 9

--

4

  1. Reconnect the IP module in-line connector.
  2. Verify that the connector position assurance (CPA) is properly installed.
  3. Install a scan tool.
  4. Turn ON the ignition, with the engine OFF.
  5. With a scan tool, request the SIR DTC display.

Does the scan tool indicate that DTC B0016 is current?

Go to Step 5

Go to Diagnostic Aids

5

  1. Turn OFF the ignition.
  2. Disconnect the IP module in-line connector. Refer to Inflatable Restraint Instrument Panel Module Replacement .
  3. Use the J 38715-100 adaptor to connect the J 38715-A SIR Load Tool to the harness side of the in-line connector.
  4. Turn ON the ignition, with the engine OFF.
  5. With a scan tool, request the SIR DTC display.

Does the scan tool indicate that DTC B0016 is current?

Go to Step 6

Go to Step 8

6

  1. Turn OFF the ignition.
  2. Remove the J 38715-A SIR Load Tool and adaptor.
  3. Disconnect the SDM connector. Refer to Inflatable Restraint Sensing and Diagnostic Module Replacement .
  4. Test the IP module high and IP module low control circuits for a short. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 9

Go to Step 7

7

Replace the SDM. Refer to Inflatable Restraint Sensing and Diagnostic Module Replacement .

Did you complete the replacement?

Go to Step 9

--

8

Replace the IP module. Refer to Inflatable Restraint Instrument Panel Module Replacement .

Did you complete the replacement?

Go to Step 9

--

9

  1. Reconnect all SIR system components.
  2. Verify that all components, connectors and CPAs are properly mounted.
  3. Use the scan tool in order to clear the DTCs.
  4. Operate the vehicle within the Conditions for Running the DTC as specified in the supporting text.

Does the DTC reset?

Go to Step 2

System OK