GM Service Manual Online
For 1990-2009 cars only

Tools Required

J-42759 Ignition Switch Connector Release Tool

Removal Procedure


    Object Number: 401496  Size: SH

    Caution: This vehicle is equipped with a Supplemental Inflatable Restraint (SIR) System. Failure to follow the correct procedure could cause the following conditions:

       • Air bag deployment
       • Personal injury
       • Unnecessary SIR system repairs
    In order to avoid the above conditions, observe the following guidelines:
       • Refer to SIR Component Views in order to determine if you are performing service on or near the SIR components or the SIR wiring.
       • If you are performing service on or near the SIR components or the SIR wiring, disable the SIR system. Refer to Disabling the SIR System.

  1. Disable the SIR system. Refer to Disabling the SIR System in SIR.
  2. Remove the steering column trim covers from the steering column. Refer to Steering Column Trim Covers Replacement - On Vehicle .
  3. Remove the knee bolster. Refer to Knee Bolster Replacement in Instrument, Panel, Gauges and Console.
  4. Disconnect the steering column electrical connectors.

  5. Object Number: 415293  Size: SH
  6. Remove the wire harness assembly (1) from the steering column and the wire harness strap (2).

  7. Object Number: 306234  Size: SH
  8. Slide the 2 connectors (2) of the turn signal and multifunction switch assembly out of the bulkhead connector (1).

  9. Object Number: 306267  Size: SH
  10. Remove the key alarm connector (1) from the lock module assembly (2) in the following way:
  11. 7.1. Rotate the key alarm connector (1) 90 degrees.
    7.2. Pull the key alarm connector (1) out of the lock module assembly (2).
  12. Remove the passkey connector from the lock module assembly (2).

  13. Object Number: 389654  Size: SH
  14. Remove the connector (2) from the electric park lock (1), for vehicles equipped with floor shifters.

  15. Object Number: 415849  Size: SH
  16. Remove the ignition switch (2) from the lock module (1) using the J-42759 .

Installation Procedure


    Object Number: 389639  Size: SH
  1. Install the ignition switch (2) into the lock module (1).

  2. Object Number: 306267  Size: SH
  3. Install the key alarm connector (1) into the lock module assembly (2).
  4. 2.1. Push the key alarm connector (1) into the lock module assembly (2).
    2.2. Rotate the key alarm connector (1) 90 degrees so that the key alarm connector (1) locks into place.
  5. Install the passkey connector into the lock module assembly (2).

  6. Object Number: 389654  Size: SH
  7. Install the connector (2) to the electric park lock (1), for vehicles equipped with floor shifters.

  8. Object Number: 306234  Size: SH
  9. Slide the 2 connectors (2) of the turn signal and multifunction switch into the bulkhead connector (1).

  10. Object Number: 415293  Size: SH
  11. Attach the wire harness assembly (1) to the steering column wire harness strap (2).

  12. Object Number: 401496  Size: SH
  13. Connect the steering column electrical connectors to the vehicle.
  14. Install the trim covers to the column. Refer to Steering Column Trim Covers Replacement - On Vehicle .
  15. Install the knee bolster. Refer to Knee Bolster Replacement in Instrument, Panel, Gauges and Console.
  16. Enable the SIR system. Refer to Enabling the SIR System in SIR.
  17. It may be necessary to reprogram the theft deterrent system if the module was replaced. Refer to Programming Theft Deterrent System Components in Theft Deterrent.