GM Service Manual Online
For 1990-2009 cars only

Special Tools

J 45722 Fuel Sender Lock Ring Wrench

Removal Procedure

Note: Clean the fuel and evaporative emission (EVAP) connections and surrounding areas prior to disconnecting the lines in order to avoid possible system contamination.


    Object Number: 1964118  Size: SH
  1. Relieve the fuel system pressure. Refer to Fuel Pressure Relief.
  2. Drain the fuel tank. Refer to Fuel Tank Draining.
  3. Loosen the fuel fill pipe vent hose clamp (2) at the fuel tank vent valve.

  4. Object Number: 1704490  Size: SH
  5. Disconnect the chassis EVAP line quick connect fitting (4) from the fuel tank line. Refer to Plastic Collar Quick Connect Fitting Service.
  6. Disconnect the fuel tank fuel feed line quick connect fitting (5) from the chassis line. Refer to Plastic Collar Quick Connect Fitting Service.
  7. Cap the fuel and EVAP lines in order to prevent possible fuel and/or EVAP system contamination.

  8. Object Number: 1704492  Size: SH
  9. Disconnect the fuel tank EVAP lines (1) from the EVAP canister. Refer to Plastic Collar Quick Connect Fitting Service.
  10. Cap the EVAP lines in order to prevent possible EVAP system contamination.
  11. Using an adjustable jack, support the fuel tank.
  12. Remove the fuel tank strap bolts.
  13. Caution: Refer to Damage to Fuel Tank Straps Caution in the Preface section.

  14. Remove the fuel tank straps.
  15. With the aid of an assistant, carefully lower the rear of the fuel tank.
  16. Slide the front of the tank away from the frame.
  17. Lower the fuel tank slightly until the chassis wiring harness electrical connectors can be accessed.

  18. Object Number: 1704493  Size: SH
  19. Disengage the chassis wiring harness electrical connector, connector position assurance (CPA) retainer at the module.
  20. Disconnect the chassis wiring harness electrical connectors (1) from the module and the fuel pressure sensor.

  21. Object Number: 1224293  Size: SH
  22. Completely lower the fuel tank.
  23. With the aid of an assistant, place the fuel tank in a suitable work area.
  24. If replacing the fuel tank proceed to the next step, otherwise proceed to step 18 in the installation procedure.

  25. Object Number: 1704504  Size: SH
  26. Remove the fuel feed line from the retaining feature (2) in the fuel tank.
  27. Open the fuel/EVAP line clip (1) and remove the fuel feed line from the clip.
  28. Disconnect the fuel feed line quick connect fitting at the fuel tank module. Refer to Plastic Collar Quick Connect Fitting Service.

  29. Object Number: 1704506  Size: SH
  30. Remove the fuel feed line from the fuel tank.

  31. Object Number: 1704741  Size: SH
  32. Remove the fuel tank shield retainers (2 and 3) and shields (1 and 4).

  33. Object Number: 1704505  Size: SH
  34. Remove the EVAP line from the fuel tank clips (2 and 6).
  35. Open the fuel tank clips (1, 3, 4, and 5) and remove the EVAP lines from the clips.
  36. Disconnect the EVAP line quick connect fittings at the fuel tank module and fuel tank vent valve. Refer to Plastic Collar Quick Connect Fitting Service.

  37. Object Number: 1704507  Size: SH
  38. Remove the EVAP lines from the fuel tank.

  39. Object Number: 1642096  Size: SH
  40. Using the J 45722 , remove the lock ring.

  41. Object Number: 1254425  Size: SH
  42. Carefully lift the module from the fuel tank, enough to access the quick connect fittings (1) under the module cover. Disconnect the quick connect fittings. Refer to Plastic Collar Quick Connect Fitting Service.
  43. Remove the fuel tank module.
  44. Remove and discard the fuel tank module seal.

  45. Object Number: 1617750  Size: SH

    Note: 

       • Some lock rings were manufactured with "DO NOT REUSE" stamped into them. These lock rings may be reused if they are not damaged or warped.
       • Inspect the lock ring for damage due to improper removal or installation procedures. If damage is found, install a NEW lock ring.
       • Check the lock ring for flatness.

  46. Place the lock ring on a flat surface. Measure the clearance between the lock ring and the flat surface using a feeler gage at 7 points.
  47. If warpage is less than 0.41 mm (0.016 in), the lock ring does not require replacement.
  48. If warpage is greater than 0.41 mm (0.016 in), the lock ring must be replaced.

Installation Procedure


    Object Number: 1254425  Size: SH
  1. If the fuel tank was replaced perform the following steps, otherwise proceed to step 18.
  2. Install the NEW fuel tank module seal onto the fuel tank.
  3. Pull the vent lines in the fuel tank up as far as possible for ease of installation.
  4. Position the fuel tank module part way into the fuel tank.
  5. Connect the quick connect fittings (1) to the module cover. Refer to Plastic Collar Quick Connect Fitting Service.
  6. Install the fuel tank module into the fuel tank.
  7. Place the lock ring into position.
  8. Note: Always replace the fuel module seal when installing the fuel module. Replace the lock ring if necessary. DO NOT apply any type of lubrication in the seal groove.

    Ensure the lock ring is installed with the correct side facing upward. A correctly installed lock ring will only turn in a clockwise direction.

  9. Rotate the lock ring counterclockwise using the J 45722 .

  10. Object Number: 1704507  Size: SH
  11. Install the EVAP lines to the fuel tank.

  12. Object Number: 1704505  Size: SH
  13. Connect the EVAP line quick connect fittings at the fuel tank module and fuel tank vent valve. Refer to Plastic Collar Quick Connect Fitting Service.
  14. Install the EVAP lines to the fuel tank clips (1, 3, 4, and 5) and close the clips.
  15. Install the EVAP line to the fuel tank clips (2 and 6).

  16. Object Number: 1704741  Size: SH
  17. Install the fuel tank shields (1 and 4) and retainers (2 and 3).

  18. Object Number: 1704506  Size: SH
  19. Install the fuel feed line to the fuel tank.

  20. Object Number: 1704504  Size: SH
  21. Connect the fuel feed line quick connect fitting at the fuel tank module. Refer to Plastic Collar Quick Connect Fitting Service.
  22. Install the fuel feed line to the clip (1) and close the clip.
  23. Install the fuel feed line to the retaining feature (2) in the fuel tank.

  24. Object Number: 1704493  Size: SH
  25. Place the fuel tank onto a suitable jack.
  26. With the aid of an assistant, partially raise the fuel tank until the electrical connections can be made.
  27. Connect the chassis wiring harness electrical connectors (1) to the fuel tank module and fuel pressure sensor.
  28. Engage the chassis harness electrical connector CPA retainer at the module electrical connector.

  29. Object Number: 1224293  Size: SH
  30. Completely raise the fuel tank.
  31. Install the fuel tank straps.
  32. Caution: Refer to Fastener Caution in the Preface section.

  33. Install the fuel tank strap bolts.
  34. Tighten
    Tighten the bolts to 40 N·m (30 lb ft).

  35. Remove the adjustable jack from the fuel tank.

  36. Object Number: 1704492  Size: SH
  37. Remove the caps from the EVAP lines.
  38. Connect the fuel tank EVAP lines (1) to the EVAP canister. Refer to Plastic Collar Quick Connect Fitting Service.

  39. Object Number: 1704490  Size: SH
  40. Remove the caps from the fuel and EVAP lines.
  41. Connect the chassis EVAP line quick connect fitting (4) to the fuel tank line. Refer to Plastic Collar Quick Connect Fitting Service.
  42. Connect the fuel tank fuel feed line quick connect fitting (5) to the chassis line. Refer to Plastic Collar Quick Connect Fitting Service.

  43. Object Number: 1964118  Size: SH
  44. Install the fuel fill pipe vent hose to the fuel tank vent valve.
  45. Tighten the fuel fill pipe vent hose clamp (2) at the fuel tank vent valve.
  46. Tighten
    Tighten the clamp to 2.5 N·m (22 lb in).

  47. Install the fuel fill hose to the fuel tank. Ensure that the notch in the hose is aligned with the notch on the fuel tank.
  48. Tighten the fuel fill hose clamp (1).
  49. Tighten
    Tighten the clamp to 2.5 N·m (22 lb in).

  50. Lower the vehicle.
  51. Refill the fuel tank.
  52. Install the fuel fill cap.
  53. Connect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection.
  54. Use the following procedure in order to inspect for leaks:
  55. 39.1. Turn the ignition ON, with the engine OFF, for 2 seconds.
    39.2. Turn the ignition OFF for 10 seconds.
    39.3. Turn the ignition ON, with the engine OFF.
    39.4. Inspect for fuel leaks.
  56. Install the intake manifold sight shield. Refer to Upper Intake Manifold Sight Shield Replacement.