GM Service Manual Online
For 1990-2009 cars only

Circuit Description

The body control module (BCM) receives a variable voltage signal from the instrument panel (I/P) dimmer switch requesting to illuminate the illumination lamps to a desired intensity. When this occurs, the BCM directly sends a variable voltage based on the I/P dimmer switch position on the instrument panel lamps dimming supply voltage circuit, instrument panel lamps dimming control circuit, and the LED dimming signal circuit.

Voltage for the instrument panel lamps dimming supply voltage circuit, instrument panel lamps dimming control circuit, and the LED dimming signal circuits is from the TBC 2 A fuse in the instrument panel fuse block directly through the BCM to these circuits.

Conditions for Running the DTC

The battery voltage must be between 9-16 volts.

Conditions for Setting the DTC

    • The instrument panel lamps dimming control circuit is open, shorted to ground, or shorted to voltage.
    • The instrument panel lamps dimming supply voltage circuit is open, shorted to ground, or shorted to voltage.
    • There is a loss of the instrument panel fuse block TBC 2 A battery supply voltage to the BCM for 1 second.

Action Taken When the DTC Sets

The illumination lamps will not operate or are always ON.

Conditions for Clearing the MIL/DTC

    • This DTC will clear on current status after the condition for setting the fault is corrected.
    • A history DTC will clear after 100 consecutive ignition cycles without a fault present.
    • History and current DTCs can be cleared using a scan tool.

Diagnostic Aids

    • Perform a visual inspection for loose or poor connections at all related components. Refer to Testing for Intermittent Conditions and Poor Connections in Wiring Systems.
    • A short to ground in the following circuits will cause the TBC 2 A fuse to open.
       - The instrument panel lamps dimming control.
       - Battery positive voltage from the instrument panel fuse block TBC 2 A fuse.
    • An open in the TBC 2 A fuse will cause the BCM to set the following DTC:
       - B0951
       - B2610
       - B2625

Test Description

The numbers below refer to the step numbers on the diagnostic table.

  1. This step test determines if the problem exists in the headlamp switch or the BCM.

  2. After replacement of the BCM you must calibrate the new module for proper operation.

Step

Action

Yes

No

Schematic Reference: Interior Lights Dimming Schematics

Connector End View Reference: Lighting Systems Connector End Views or Body Control System Connector End Views in Body Control System

1

Did you perform the Lighting System Diagnostic System Check?

Go to Step 2

Go to Diagnostic System Check - Lighting Systems

2

Is the TBC 2 A fuse in the instrument panel fuse block open?

Go to Step 3

Go to Step 4

3

Test the instrument panel lamps dimming control circuit for a short to ground. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 11

Go to Step 8

4

Test the instrument panel lamps dimming supply voltage circuit and the instrument panel lamps dimming control circuit for an open, high resistance, short to voltage or short to ground. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 11

Go to Step 5

5

  1. Ensure that the headlamp switch is in the on position.
  2. Ensure that the instrument panel dimmer switch is in the full bright position.
  3. With the headlamp switch still connected, connect a test lamp between the instrument panel lamps dimming control circuit and the ground circuit of the headlamp switch connector.

Does the test lamp illuminate?

Go to Step 6

Go to Step 7

6

Inspect for poor connections at the harness connector of the headlamp switch. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 11

Go to Step 9

7

Inspect for poor connections at the harness connector of the body control module (BCM). Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 11

Go to Step 10

8

Repair the battery positive voltage circuit of the BCM from the TBC 2 A fuse in the instrument panel fuse block. Refer to Wiring Repairs in Wiring Systems.

Did you complete the repair?

Go to Step 11

--

9

Replace the headlamp and panel dimmer switch. Refer to Headlamp Switch Replacement .

Did you complete the replacement?

Go to Step 11

--

10

Important: Perform the setup procedure for the BCM.

Replace the BCM. Refer to Body Control Module Replacement in Body Control System.

Did you complete the replacement?

Go to Step 11

--

11

  1. Use the scan tool in order to clear the DTCs.
  2. Operate the vehicle within the Conditions for Running the DTC as specified in the supporting text.

Does the DTC reset?

Go to Step 2

System OK