GM Service Manual Online
For 1990-2009 cars only

Tools Required

    • J 36660-A Torque Angle Meter
    • J 42385-200 Thread Repair Kit

Removal Procedure

  1. Remove the oil level indicator. Refer to Oil Level Indicator and Tube Replacement .
  2. Remove the intake manifold. Refer to Intake Manifold Replacement .
  3. Remove the coolant air bleed pipe. Refer to Coolant Air Bleed Pipe Assembly Replacement in Engine Cooling.
  4. Remove the right exhaust manifold. Refer to Exhaust Manifold Replacement - Right Side in Engine Exhaust.
  5. Remove the pushrods. Refer to Valve Rocker Arm and Push Rod Replacement .

  6. Object Number: 832959  Size: SH

    Important: The cylinder head bolts are NOT reusable.

  7. Remove and discard the cylinder head bolts (1, 2, 3).

  8. Object Number: 832960  Size: SH

    Notice: After removal, place the cylinder head on 2 wood blocks in order to prevent damage to the sealing surfaces.

  9. Remove the cylinder head.

  10. Object Number: 832965  Size: SH
  11. Remove and discard the cylinder head gasket.
  12. If required, clean and inspect the cylinder head. Refer to Cylinder Head Cleaning and Inspection .

Installation Procedure

Caution: Wear safety glasses in order to avoid eye damage.

Notice: Clean all dirt, debris, and coolant from the engine block cylinder head bolt holes. Failure to remove all foreign material may result in damaged threads, improperly tightened fasteners or damage to components.

Important: 

   • Do not reuse the cylinder head bolts. Install NEW cylinder head bolts during assembly.
   • Do not use any type of sealant on the cylinder head gasket, unless specified.
   • The cylinder head gaskets must be installed in the proper direction and position.


    Object Number: 832970  Size: SH
  1. Clean the engine block cylinder head bolt holes, if required.
  2. Thread repair tool J 42385-107, found in J 42385-200 may be used to clean the threads of old threadlocking material.

  3. Use spray cleaner GM P/N 12346139, P/N 12377981, (Canadian P/N 10953463) or equivalent into the hole.
  4. Clean the cylinder head bolt holes with compressed air.
  5. Check the cylinder head locating pins for proper installation, location (a) 8.3 mm (0.327 in).

  6. Object Number: 832967  Size: SH
  7. When properly installed, with FRONT on the right side, the tab on the cylinder head gasket should be located right of center or closer to the front of the engine.

  8. Object Number: 832965  Size: SH
  9. Install the NEW cylinder head gasket.

  10. Object Number: 832960  Size: SH
  11. Install the cylinder head.

  12. Object Number: 832959  Size: SH
  13. Install the NEW cylinder head bolts.

  14. Object Number: 832971  Size: SH

    Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

  15. Tighten the cylinder head bolts.
  16. Tighten

    1. Tighten the M11 bolts a first pass in sequence to 30 N·m (22 lb ft).
    2. Tighten the M11 bolts a second pass in sequence to 90 degrees using J 36660-A .
    3. Tighten the M11 bolts (1, 2, 3, 4, 5, 6, 7, 8) to 90 degrees and the M11 bolts (9 and 10) to 50 degrees a final pass in sequence using J 36660-A .
    4. Tighten the M8 bolts (11, 12, 13, 14, 15) to 30 N·m (22 lb ft). Begin with the center bolt (11) and alternating side-to-side, work outward tightening all of the bolts.
  17. Install the pushrods. Refer to Valve Rocker Arm and Push Rod Replacement .
  18. Install the right exhaust manifold. Refer to Exhaust Manifold Replacement - Right Side in Engine Exhaust.
  19. Install the coolant air bleed pipe. Refer to Coolant Air Bleed Pipe Assembly Replacement in Engine Cooling.
  20. Install the intake manifold. Refer to Intake Manifold Replacement .
  21. Install the oil level indicator. Refer to Oil Level Indicator and Tube Replacement .