1. Remove the engine sight shield, if required. Refer to Upper Intake Manifold Sight Shield Replacement .
2. Remove the connector position assurance (CPA) lock.
3. Disconnect the main electrical connector (1) feeding the ignition coils.
4. Remove the harness clips (2).
5. Reposition the engine harness, if necessary.
6. Remove the spark plug wires from the ignition coils.

•	Twist each plug wire 1/2 turn.

•	Pull only on the boot in order to remove the wire from the ignition coil.




7. If equipped with the 4.8L, 5.3L, or 6.0L (LQ4) engine, perform the following:

7.1.	Reposition the surge tank/heater hoses from the heater hose bracket.

7.2.	Remove the heater hose bracket nut and bracket.




8. Remove the ignition coil bracket studs from the rocker arm cover.
9. Remove the ignition coils and bracket from the rocker cover.



10. Remove the positive crankcase ventilation (PCV) hose from the throttle body and rocker cover.



11. Remove the valve rocker arm cover bolts.
12. Remove the valve rocker arm cover.



13. Remove the gasket (1) from the rocker cover.
14. Discard the OLD gasket.



15. Remove the oil fill cap from the oil fill tube.
16. Remove the oil fill tube from the rocker cover, if required.
17. Discard the oil fill tube.
18. Clean and inspect the rocker arm cover. Refer to Valve Rocker Arm Cover Cleaning and Inspection in Engine Mechanical - 4.8L, 5.3L, and 6.0L Unit Repair.

Important: 

1. Lubricate the O-ring seal of the NEW oil fill tube with clean engine oil.
2. Insert the NEW oil fill tube into the rocker arm cover.

Rotate the tube clockwise until locked in the proper position.

3. Install the oil fill cap into the tube.

Rotate the cap clockwise until locked in the proper position.




4. Install a NEW rocker cover gasket (1) into the valve rocker cover lip.



5. Install the valve rocker arm cover onto the cylinder head.
6. Install new rocker arm cover grommets, if necessary.

Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

7. Install the rocker arm cover bolts and grommets.

Tighten
Tighten the bolts to 12 N·m (106 lb in).




8. Install the PCV hose to the throttle body and rocker cover.



9. Apply threadlock GM P/N 12345382, Canada P/N 10953489, or equivalent to the threads of the bracket bolts.
10. Install the ignition coils and bracket to the rocker arm cover.
11. Install the ignition coil bracket studs to the rocker cover.

Tighten
Tighten the studs to 12 N·m (106 lb in).




12. If equipped with the 4.8L, 5.3L, or 6.0L (LQ4) engine, perform the following:

12.1.

Install the heater hose bracket and nut.

Tighten
Tighten the nut to 9 N·m (80 lb in).

12.2.

Position the surge tank/heater hoses to the heater hose bracket.




13. Install the spark plug wires to the ignition coils.
14. Position the engine harness, if necessary.
15. Install the harness clips (2).
16. Connect the main electrical connector (1) feeding the ignition coils.
17. Install the CPA lock.
18. Install the engine sight shield, if required. Refer to Upper Intake Manifold Sight Shield Replacement .