GM Service Manual Online
For 1990-2009 cars only

Liftgate Emblem/Nameplate Replacement Tahoe


Object Number: 1669881  Size: SF

Callout

Component Name

1

Liftgate Emblem Assembly (Tahoe)

Notice: Refer to Exterior Trim Emblem Removal Notice in the Preface section.

Tip

  1. The part and surface should be 21°C (70°F) prior to installation. The vehicle should remain 21°C (70°F) for one hour after assembly to allow adhesive to develop sufficient bond strength.
  2. Use a J 25070 Heat Gun or equivalent to remove the old emblem. Clean all adhesive from rear liftgate and wipe the surface dry with a clean lint-free towel prior to installing the new emblem.
  3. When removing protective liners from the adhesive tape, be careful not to touch tape with hands and do not allow tape to come in contact with dirt or any foreign matter prior to adhesion.
  4. Close the liftgate lid.
  5. Wet out the emblem and ensure full adhesion of the emblem to the liftgate is made.

Liftgate Emblem/Nameplate Replacement Escalade


Object Number: 1669833  Size: SF

Callout

Component Name

1

Liftgate Nameplate Assembly (Escalade)

Notice: Refer to Exterior Trim Emblem Removal Notice in the Preface section.

Tip

  1. The part and surface should be 21°C (70°F) prior to installation. The vehicle should remain 21°C (70°F) for one hour after assembly to allow adhesive to develop sufficient bond strength.
  2. Use a J 25070 Heat Gun or equivalent to remove the old nameplate/emblem. Clean all adhesive from rear liftgate and wipe the surface dry with a clean lint-free towel prior to installing the new emblem.
  3. When removing protective liners from the adhesive tape, be careful not to touch tape with hands and do not allow tape to come in contact with dirt or any foreign matter prior to adhesion.
  4. Close the liftgate lid.
  5. Wet out the nameplate/emblem and ensure full adhesion of the nameplate is made to the liftgate.

Liftgate Emblem/Nameplate Replacement Tahoe FFU


Object Number: 1833025  Size: MF

Callout

Component Name

1

Flex Fuel Badge

Notice: Refer to Exterior Trim Emblem Removal Notice in the Preface section.

Tip

  1. The part and surface should be 21°C (70°F) prior to installation. The vehicle should remain 21°C (70°F) for one hour after assembly to allow adhesive to develop sufficient bond strength.
  2. Use a J 25070 Heat Gun or equivalent to remove the old emblem. Clean all adhesive from rear liftgate and wipe the surface dry with a clean lint-free towel prior to installing the new emblem / nameplate.
  3. When removing protective liners from the adhesive tape, be careful not to touch tape with hands and do not allow tape to come in contact with dirt or any foreign matter prior to adhesion.
  4. Close the liftgate.
  5. Wet out the emblem and ensure full adhesion of the emblem to the liftgate is made.

Liftgate Emblem/Nameplate Replacement Suburban FFU


Object Number: 1833028  Size: MF

Callout

Component Name

1

Flex Fuel Badge

Notice: Refer to Exterior Trim Emblem Removal Notice in the Preface section.

Tip

  1. The part and surface should be 21°C (70°F) prior to installation. The vehicle should remain 21°C (70°F) for one hour after assembly to allow adhesive to develop sufficient bond strength.
  2. Use a J 25070 Heat Gun or equivalent to remove the old emblem. Clean all adhesive from rear liftgate and wipe the surface dry with a clean lint-free towel prior to installing the new emblem / nameplate.
  3. When removing protective liners from the adhesive tape, be careful not to touch tape with hands and do not allow tape to come in contact with dirt or any foreign matter prior to adhesion.
  4. Close the liftgate.
  5. Wet out the emblem and ensure full adhesion of the emblem to the liftgate is made.

Liftgate Emblem/Nameplate Replacement Yukon and Yukon XL FFU


Object Number: 1833029  Size: MF

Callout

Component Name

1

Flex Fuel Badge

Notice: Refer to Exterior Trim Emblem Removal Notice in the Preface section.

Tip

  1. The part and surface should be 21°C (70°F) prior to installation. The vehicle should remain 21°C (70°F) for one hour after assembly to allow adhesive to develop sufficient bond strength.
  2. Use a J 25070 Heat Gun or equivalent to remove the old emblem. Clean all adhesive from rear liftgate and wipe the surface dry with a clean lint-free towel prior to installing the new emblem / nameplate.
  3. When removing protective liners from the adhesive tape, be careful not to touch tape with hands and do not allow tape to come in contact with dirt or any foreign matter prior to adhesion.
  4. Close the liftgate.
  5. Wet out the emblem and ensure full adhesion of the emblem to the liftgate is made.

Liftgate Emblem/Nameplate Replacement HP2 HyBRID


Object Number: 2039340  Size: MF

Callout

Component Name

1

Liftgate Nameplate Assembly (HyBRID)

Notice: Refer to Exterior Trim Emblem Removal Notice in the Preface section.

Procedures

  1. The part and surface should be 21°C (70°F) prior to installation. The vehicle should remain 21°C (70°F) for one hour after assembly to allow adhesive to develop sufficient bond strength.
  2. Use a J 25070 Heat Gun or equivalent to remove the old nameplate/emblem. Clean all adhesive from rear liftgate and wipe the surface dry with a clean lint-free towel prior to installing the new emblem.
  3. When removing protective liners from the adhesive tape, be careful not to touch tape with hands and do not allow tape to come in contact with dirt or any foreign matter prior to adhesion.
  4. Close the liftgate lid.
  5. Wet out the nameplate/emblem and ensure full adhesion of the nameplate is made to the liftgate.

Special Tool

J 25070 500°-750° F Heat Gun