DTC B0560. GMC Truck TopKick C-Series (Crew) C4/C5 2003

For 1990-2009 cars only

Makes 🢒 GMC_Truck 🢒 2003 🢒 TopKick C-Series (Crew) C4/C5 🢒 DTC 🢒 DTC B0560

Circuit Description

The PCM creates the engine speed signal by pulsing the signal circuit to ground at the rate of 2 pulses per engine revolution. The IPC converts the signal to a tachometer position. The IPC also receives a class 2 message from the PCM indicating the engine speed. The IPC uses this class 2 message for diagnostic purposes.

Conditions for Running the DTC

•	The IPC receives a class 2 message from the PCM indicating that the engine speed is greater than 800 RPM.

•	The ignition voltage is between 9.0 volts and 18 volts.

Conditions for Setting the DTC

•	The IPC does not detect a 2 pulses per engine revolution signal on the engine speed signal circuit.

•	The above condition is present for at least 5.0 seconds.

Action Taken When the DTC Sets

The IPC stores a DTC B0560 in memory.

Conditions for Clearing the DTC

•	A history DTC clears after 100 malfunction free warm-up cycles.

•	The DTC becomes history when the conditions for setting the DTC are no longer present.

•	The IPC receives the clear code command from the scan tool.

Step

Action

Values

Yes

Schematic Reference: Instrument Cluster Schematics

Connector End View Reference: Master Electrical Component List in Wiring Systems

Did you perform the Instrument Cluster Diagnostic System Check?

Go to Step 2

Go to Diagnostic System Check - Instrument Cluster

Install a scan tool.
Start the engine.
With the scan tool, observe the Engine Speed parameter in the PCM Engine Data 1 data list.

Does the Engine Speed parameter match the tachometer display?

Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems

Go to Step 3

Turn the ignition OFF.
Disconnect the PCM connector C2 (L18 and LB7) or C3 (LG4).
Turn the ignition ON, with the engine OFF.
Measure the voltage from the engine speed signal circuit of the PCM to a good ground.

Does the voltage measure greater than the specified value?

9.0 V

Go to Step 4

Go to Step 5

Test the engine speed signal circuit for a short to voltage. Refer to Circuit Testing and to Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 10

Go to Step 6

Test the engine speed signal circuit for an open or for a short to ground. Refer to Circuit Testing and to Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 10

Go to Step 7

Inspect for poor connections at the harness connector of the PCM. Refer to Testing for Intermittent Conditions and Poor Connections and to Connector Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 10

Go to Step 8

Inspect for poor connections at the harness connector of the IPC. Refer to Testing for Intermittent Conditions and Poor Connections and to Connector Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 10

Go to Step 9

Important: Program the replacement PCM.

Replace the PCM. Refer to:

•	Engine Control Module Replacement in Engine Controls - 6.6L.

•	Engine Control Module Replacement/Restore Fuel Rate Data in Engine Controls - 7.8L.

•	Powertrain Control Module Replacement in Engine Controls - 8.1L.

Did you complete the replacement?

Go to Step 10

Important: Program the replacement IPC

Replace the IPC. Refer to Instrument Cluster Replacement .

Did you complete the replacement?

Go to Step 10

Use the scan tool in order to clear the DTCs.
Operate vehicle within the Conditions for Running this DTC.

Does the DTC reset?

Go to Step 2

System OK