GM Service Manual Online
For 1990-2009 cars only

Transfer Case Speed Sensor Replacement Front

Removal Procedure


    Object Number: 651506  Size: SH
  1. Raise the vehicle. Refer to Lifting and Jacking the Vehicle in General Information.
  2. Remove the transfer case shield. Refer to Transfer Case Shield Replacement .
  3. Remove the transfer case front speed sensor electrical connector.

  4. Object Number: 163707  Size: SH
  5. Remove the transfer case front speed sensor.

Installation Procedure


    Object Number: 163707  Size: SH

    Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

  1. Install the transfer case front speed sensor.
  2. Tighten
    Tighten the transfer case front speed sensor to 15 N·m (11 lb ft).


    Object Number: 651506  Size: SH
  3. Install the transfer case front speed sensor electrical connector.
  4. Install the transfer case shield. Refer to Transfer Case Shield Replacement .
  5. Lower the vehicle. Refer to Lifting and Jacking the Vehicle in General Information.

Transfer Case Speed Sensor Replacement Right Rear

Removal Procedure


    Object Number: 648197  Size: SH
  1. Raise the vehicle. Refer to Lifting and Jacking the Vehicle in General Information.
  2. Remove the transfer case shield. Refer to Transfer Case Shield Replacement .
  3. Remove the transfer case right rear speed sensor electrical connector.
  4. Remove the transfer case speed sensor.

Installation Procedure


    Object Number: 648197  Size: SH

    Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

  1. Install the transfer case right rear speed sensor.
  2. Tighten
    Tighten the transfer case right rear speed sensor to 15 N·m (11 lb ft).

  3. Install the transfer case right rear speed sensor electrical connector.
  4. Install the transfer case shield. Refer to Transfer Case Shield Replacement .
  5. Lower the vehicle. Refer to Lifting and Jacking the Vehicle in General Information.

Transfer Case Speed Sensor Replacement Left Rear

Removal Procedure


    Object Number: 648202  Size: SH
  1. Raise the vehicle. Refer to Lifting and Jacking the Vehicle in General Information.
  2. Remove the transfer case left rear speed sensor electrical connector.
  3. Remove the transfer case left rear speed sensor.

Installation Procedure


    Object Number: 648202  Size: SH

    Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

  1. Install the transfer case left rear speed sensor into the transfer case.
  2. Tighten
    Tighten the transfer case left rear speed sensor to 15 N·m (11 lb ft).

  3. Install the transfer case left rear speed sensor electrical connector.
  4. Lower the vehicle. Refer to Lifting and Jacking the Vehicle in General Information.