Rear Axle Lubricant Replacement 8.6 Inch Axle

1. Raise the vehicle. Refer to Lifting and Jacking the Vehicle .



2. Remove the rear axle fill plug.



3. Remove the rear axle housing cover bolts (1). Discard the rear axle housing cover bolts.
4. Carefully remove the rear axle housing cover (2) and drain the lubricant into a suitable container.
5. Remove any gasket material from the rear axle housing and/or the rear axle housing cover.
6. Inspect the bottom of the rear axle housing for excessive metal particle accumulation. This accumulation is an indication of extreme wear.

1. Install a new gasket and the rear axle housing cover (2).

Notice: Refer to Fastener Notice in the Preface section.

Important: Do not reuse the rear axle housing cover bolts.

2. Install the new rear axle housing cover bolts (1).

Tighten
Tighten the bolts to 40 N·m (30 lb ft).

3. Fill the rear axle. Use the proper fluid. Refer to Approximate Fluid Capacities and Fluid and Lubricant Recommendations .



4. Install the rear axle fill plug.

Tighten
Tighten the rear axle fill plug to 33 N·m (24 lb ft).

5. Lower the vehicle.

Rear Axle Lubricant Replacement 9.5 LD Axle

1. Raise the vehicle. Refer to Lifting and Jacking the Vehicle .



2. Remove the rear axle fill plug.



3. Remove the rear axle drain plug.
4. Drain the lubricant into a suitable container.
5. Inspect the drain plug for excessive metal particle accumulation. This accumulation is symptomatic of extreme wear.
6. Clean the drain plug.

Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.




1. Install the rear axle drain plug.

Tighten
Tighten the rear axle drain plug to 33 N·m (24 lb ft).

2. Fill the rear axle. Use the proper fluid. Refer to Approximate Fluid Capacities and Fluid and Lubricant Recommendations .



3. Install the rear axle fill plug.

Tighten
Tighten the rear axle fill plug to 33 N·m (24 lb ft).

4. Lower the vehicle.

Rear Axle Lubricant Replacement 9.5 Inch HDand 10.5 Inch Axles

1. Raise the vehicle. Refer to Lifting and Jacking the Vehicle .



2. For the 9.5/9.5LD and the 10.5 inch axles, remove the rear axle fill plug.



3. For the 11.5 inch axle, remove the fill plug.



4. Remove the rear axle drain plug.
5. Drain the lubricant into a suitable container.
6. Inspect the drain plug for excessive metal particle accumulation. This accumulation is symptomatic of extreme wear.
7. Clean the drain plug.

Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.




1. Install the rear axle drain plug.

Tighten
Tighten the rear axle drain plug to 33 N·m (24 lb ft).

2. Fill the rear axle. Use the proper fluid. Refer to Approximate Fluid Capacities and Fluid and Lubricant Recommendations .



3. For the 9.5/9.5LD and the 10.5 inch axles, install the rear axle fill plug.

Tighten
Tighten the rear axle fill plug to 33 N·m (24 lb ft).




4. For the 11.5 inch axle, install the seal and the fill plug.

Tighten
Tighten the rear axle fill plug to 33 N·m (24 lb ft).

5. Lower the vehicle.