GM Service Manual Online
For 1990-2009 cars only

Tools Required

J 41712 Oil Pressure Switch Socket or equivalent


    Object Number: 1276785  Size: SH

    Important: 

       • Engine block plug, oil gallery and coolant, sealing washers may be used again if not bent, scored or otherwise damaged.
       • Apply the proper amount and type of sealant to the sealing washer as recommended in the service procedure.

  1. Apply a 3.175 mm (0.125 in) bead of sealant GM P/N 12346004 (Canadian P/N 10953480) to the engine block coolant heater sealing washer, if applicable. Refer to Adhesives, Fluids, Lubricants, and Sealers .
  2. Notice: Refer to Fastener Notice in the Preface section.

  3. Install the engine block coolant heater to the engine block, if applicable.
  4. Tighten
    Tighten the block coolant heater to 50 N·m (37 lb ft).


    Object Number: 63165  Size: SH
  5. Apply a 3.175 mm (0.125 in) bead of sealant GM P/N 12346004 (Canadian P/N 10953480) to the engine block left front coolant drain hole plug sealing washer, if applicable.
  6. Install the engine block left front coolant drain plug, if applicable.
  7. Tighten
    Tighten the block left front coolant drain hole plug to 60 N·m (44 lb ft).


    Object Number: 63164  Size: SH
  8. Apply a 3.175 mm (0.125 in) bead of sealant GM P/N 12346004 (Canadian P/N 10953480) to the engine block right rear coolant drain hole plug sealing washer.
  9. Install the engine block right rear coolant drain plug.
  10. Tighten
    Tighten the block right rear coolant drain hole plug to 60 N·m (44 lb ft).


    Object Number: 260139  Size: SH
  11. Apply a 3.175 mm (0.125 in) bead of sealant GM P/N 12346004 (Canadian P/N 10953480) to the engine block left front oil gallery plug sealing washer.
  12. Install the engine block left front oil gallery plug.
  13. Tighten
    Tighten the block left front oil gallery plug to 60 N·m (44 lb ft).


    Object Number: 64923  Size: SH
  14. Apply a 3.175 mm (0.125 in) bead of sealant GM P/N 12346004 (Canadian P/N 10953480) to the engine block left rear oil gallery plug sealing washer.
  15. Install the engine block left rear oil gallery plug.
  16. Tighten
    Tighten the block left rear oil gallery plug to 60 N·m (44 lb ft).


    Object Number: 63228  Size: MH
  17. Inspect the engine block rear oil gallery plug and O-ring seal. If the O-ring seal on the plug is not cut or damaged, the rear oil gallery plug may be used again.
  18. Lubricate the O-ring seal with clean engine oil.
  19. Install the block rear oil gallery plug into the oil gallery bore. A properly installed block plug will protrude 0.8-1.4 mm (0.0315-0.055 in) beyond the rear face of the block.

  20. Object Number: 64295  Size: SH

    Important: The engine block front oil gallery plug should not be removed unless service is required.

  21. Apply threadlock GM P/N 12345382 (Canadian P/N 10953489) to the sides of the NEW front oil gallery plug.
  22. Install a NEW engine block front oil gallery plug, if required. Install the front oil gallery plug into the oil gallery bore 2.2-2.8 mm (0.0086-0.011 in) below flush.

  23. Object Number: 823316  Size: SH
  24. Apply sealant to the threads of the oil pressure sensor.
  25. Use the J 41712 or equivalent in order to install the oil pressure sensor.
  26. Tighten
    Tighten the oil pressure sensor to 35 N·m (26 lb ft).