GM Service Manual Online
For 1990-2009 cars only

DTC C0220-C0229 W/O JL4

Circuit Description

During an ABS event, the EBCM calculates the total time that a dump valve is energized while attempting to unlock a locked wheel.

Conditions for Running the DTC

    • The ignition is ON.
    • The vehicle is experiencing an ABS event.

Conditions for Setting the DTC

The total dump time for any dump valve has exceeded 9 seconds and the EBCM has not received a wheel speed signal from the corresponding wheel during this activity.

Action Taken When the DTC Sets

    • The EBCM disables the ABS/DRP.
    • The ABS indicator turns ON.
    • The brake warning indicator turns ON.

The actions above are maintained during subsequent ignition cycles until the EBCM completes a power up self-test. This test concludes when the vehicle achieves a speed greater than 13 km/h (8 mph) and the wheel speeds are verified by the EBCM.

Conditions for Clearing the DTC

The Conditions for Setting the DTC are no longer present and you use the scan tool Clear DTCs function.

Diagnostic Aids

The most likely cause of this DTC is a mechanical failure that causes a wheel to lock and remain locked. The DTC may also set, conceivably, when the ABS is activated on surfaces that are nearly impossible to get traction on. If the DTC sets within these conditions, diagnosis of the ABS system is not necessary.

Test Description

The number below refers to the step number on the diagnostic table.

  1. Performing Solenoid Tests determines if there is a mechanical malfunction inside the BPMV.

Step

Action

Yes

No

1

Did you perform the ABS Diagnostic System Check?

Go to Step 2

Go to Diagnostic System Check - ABS

2

  1. Use a scan tool in order to clear the DTCs.
  2. Use the scan tool in order to perform the necessary Solenoid Tests. Refer to Scan Tool Output Controls .

Do the Solenoid Tests show the system to be functioning normally?

Go to Diagnostic Aids

Go to Step 3

3

Replace the BPMV. Refer to Brake Pressure Modulator Valve Replacement .

Did you complete the replacement?

Go to Step 4

--

4

Use the scan tool in order to perform the necessary Solenoid Tests.

Do the Solenoid Tests show the system to be functioning normally?

System OK

Go to Step 3

DTC C0220-C0229 W/JL4

Circuit Description

During an ABS event, the electronic brake control module (EBCM) calculates the total time that a dump valve is energized while attempting to unlock a locked wheel.

Conditions for Running the DTC

    • The ignition is ON.
    • The vehicle is experiencing an ABS event.

Conditions for Setting the DTC

C0220

The total dump valve ON time for the left front brake circuit has exceeded 9 seconds and the EBCM has not received a wheel speed signal from the left front wheel during this activity.

C0221

The total dump valve ON time for the right front brake circuit has exceeded 9 seconds and the EBCM has not received a wheel speed signal from the right front wheel during this activity.

C0228

The total dump valve ON time for the left rear brake circuit has exceeded 9 seconds and the EBCM has not received a wheel speed signal from the left rear wheel during this activity.

C0229

The total dump valve ON time for the right rear brake circuit has exceeded 9 seconds and the EBCM has not received a wheel speed signal from the right rear wheel during this activity.

Action Taken When the DTC Sets

    • The EBCM disables the ABS/DRP.
    • The ABS indicator turns ON.
    • The brake warning indicator turns ON.

The actions above are maintained during subsequent ignition cycles until the EBCM completes a power up self-test. This test concludes when the vehicle achieves a speed greater than 13 km/h (8 mph) and the wheel speeds are verified by the EBCM.

Conditions for Clearing the DTC

The Conditions for Setting the DTC are no longer present and you use the scan tool Clear DTCs function.

Diagnostic Aids

The most likely cause of this DTC is a mechanical failure that causes a wheel to lock and remain locked. The DTC may also set, conceivably, when the ABS is activated on surfaces that are nearly impossible to get traction on. If the DTC sets within these conditions, diagnosis of the ABS system is not necessary.

Test Description

The number below refers to the step number on the diagnostic table.

  1. Performing Solenoid Tests determines if there is a mechanical malfunction inside the BPMV.

Step

Action

Yes

No

1

Did you perform the ABS Diagnostic System Check?

Go to Step 2

Go to Diagnostic System Check - ABS

2

  1. Use a scan tool in order to clear the DTCs.
  2. Use the scan tool in order to perform the necessary Solenoid Tests. Refer to Scan Tool Output Controls .

Do the Solenoid Tests show the system to be functioning normally?

Go to Diagnostic Aids

Go to Step 3

3

Replace the BPMV. Refer to Brake Pressure Modulator Valve Replacement .

Did you complete the replacement?

Go to Step 4

--

4

Use the scan tool in order to perform the necessary Solenoid Tests.

Do the Solenoid Tests show the system to be functioning normally?

System OK

Go to Step 3