Electronic Brake Control Module Replacement w/JL4

Important: After installation, calibrate the new electronic brake control module (EBCM) to the tire size that is appropriate to the vehicle.

1. Disconnect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection in Engine Electrical.
2. Raise and suitably support the vehicle. Refer to Lifting and Jacking the Vehicle in General Information.




Important: The area around the electric hydraulic control unit (EHCU) MUST be free from loose dirt to prevent contamination of disassembled ABS components.

3. Thoroughly wash all contaminants from around the EHCU.



4. For cutaway vehicles, remove the splash shield.
5. Disconnect the electrical connectors from the EBCM.



6. Remove the mounting screws that fasten the EBCM (2) to the BPMV (1).
7. Remove the EBCM (2) from the brake pressure modulator valve (BPMV) (1). Removal may require a light amount of force.
8. Clean the BPMV to EBCM mounting surfaces with a clean cloth.

Important: Do not use RTV or any other type of sealant on the EBCM gasket or mating surfaces.

1. Install the EBCM (2) on to the BPMV (1).

Notice: Refer to Fastener Notice in the Preface section.

2. Install the screws to the EBCM (2).

Tighten
Tighten the screws to 5 N·m (44 lb in) in an X-pattern.




3. Connect the electrical connectors to the EBCM.



4. For cutaway vehicles, install the splash shield.

Tighten
Tighten the splash shield bolts to 25 N·m (18 lb ft).

5. Lower the vehicle.
6. Connect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection in Engine Electrical.
7. Revise the tire calibration using the Tire Size Calibration function.
8. Verify correct system operation. Refer to Diagnostic Starting Point - Antilock Brake System .

Electronic Brake Control Module Replacement w/o JL4

Important: After installation, calibrate the new electronic brake control module (EBCM) to the tire size that is appropriate to the vehicle.

1. Disconnect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection in Engine Electrical.
2. Raise and suitably support the vehicle. Refer to Lifting and Jacking the Vehicle in General Information.




Important: The area around the electric hydraulic control unit (EHCU) MUST be free from loose dirt to prevent contamination of disassembled ABS components.

3. Thoroughly wash all contaminants from around the EHCU.



4. For cutaway vehicles, remove the splash shield.
5. Disconnect the electrical connectors from the EBCM.



6. Remove the mounting screws that fasten the EBCM (2) to the brake pressure modulator valve (BPMV) (1).
7. Remove the EBCM (2) from the BPMV (1). Removal may require a light amount of force.
8. Clean the BPMV to EBCM mounting surfaces with a clean cloth.

Important: Do not use RTV or any other type of sealant on the EBCM gasket or mating surfaces.

1. Install the EBCM (2) on to the BPMV (1).

Notice: Refer to Fastener Notice in the Preface section.

2. Install the screws to the EBCM (2).

Tighten
Tighten the screws to 5 N·m (44 lb in) in an X-pattern.




3. Connect the electrical connectors to the EBCM.



4. For cutaway vehicles, install the splash shield.

Tighten
Tighten the splash shield bolts to 25 N·m (18 lb ft).

5. Lower the vehicle.
6. Connect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection in Engine Electrical.
7. Revise the tire calibration using the Tire Size Calibration function.
8. Verify correct system operation. Refer to Diagnostic Starting Point - Antilock Brake System .