GM Service Manual Online
For 1990-2009 cars only

Diagnostic Instructions

    • Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure.
    • Review Strategy Based Diagnosis for an overview of the diagnostic approach.
    •  Diagnostic Procedure Instructions provides an overview of each diagnostic category.

DTC Descriptors

DTC B1370 01: Device Ignition 1 (ON and START) Circuit Short to Battery

DTC B1370 06: Device Ignition 1 (ON and START) Circuit Short to Ground or Open

DTC B1380 01: Device Ignition ACCESSORY Circuit Short to Battery

DTC B1380 06: Device Ignition ACCESSORY Circuit Short to Ground or Open

DTC B1440 00: Power Mode Master Input Circuits Mismatch

DTC B1441 01: Device Ignition OFF, RUN, and CRANK Circuit Short to Battery

DTC B1441 06: Device Ignition OFF, RUN, and CRANK Circuit Short to Ground or Open

Diagnostic Fault Information

Circuit

Short to Ground

Open/High Resistance

Short to Voltage

Signal Performance

B+

B1370 06, B1380 06, U0100-U0299, 2, 4

B1370 06, B1380 06, U0100-U0299

--

--

Accessory Voltage

B1370 06, B1380 06, U0100-U0299, 2, 4

B1380 06, 1

B1380 01, P1629, 1

--

Ignition 1 Voltage

B1370 06, B1380 06, U0100-U0299, 2, 4

B1370 06, 1

B1370 01, U0100-U0299, 1, 2

--

Off/Run/Crank Voltage

B1370 06, B1380 06, U0100-U0299, 2, 4

1

1

--

Run/Crank Ignition 1 Voltage

B1428, 3

B1370 06

--

--

Accessory Wakeup Serial Data

U1814, 3

U0100-U0299, P0513 00

--

--

  1. Power Mode Mismatch
  2. Scan Tool Does Not Communicate with High Speed GMLAN Device
  3. This circuit is a pass through circuit in the BCM and will cause Ign Switch fuse to open.
  4. This circuit/condition will cause B+ fuse to open, and may cause a no start condition.

Circuit/System Description

The vehicle power mode master (PMM) is the body control module (BCM). The ignition switch is a low current switch with multiple discrete ignition switch signals to the PMM for determination of the power mode. The PMM receives the ignition switch signals, and additionally a reference voltage signal from the BCM, through the ignition switch, and back to the BCM. There are redundancies within the PMM system that can allow operation of certain subsystems when there are faults in the ignition switch circuits. Other information such as serial data input from other modules and DTCs is also used to determine what power mode signals and information is transmitted by the PMM. The BCM logic uses all this information to identify the operator's desired power mode and activate specific discrete signals, and serial data messages for the operation of different subsystems as necessary. Other modules which have switched voltage inputs may operate in a default mode if the PMM serial data message does not match what the individual module can detect from its own connections.

The PMM will activate relays and other direct outputs of the PMM as needed according to the calculated power mode. Some relays controlled by the BCM are switched ignition voltage outputs that are pass through circuits within the BCM directly from the ignition switch. If these circuits short to ground, the B+ circuit fuse to the ignition switch will open.

Conditions for Running the DTC

B1370 01

Ignition switch is in the OFF or ACC positions.

B1370 06, B1380 01, B1441 01, B1441 06

Ignition switch is in the START position.

B1380 06, B1440 00

Ignition switch is in the RUN position.

Conditions for Setting the DTC

B1370 01

Ignition 1 voltage circuit is shorted to voltage.

B1370 06

    • Ignition 1 voltage circuit is open.
    • Ignition 1 voltage, accessory voltage, or off/run/crank voltage circuit shorted to ground.
    • B+ circuit of the ignition switch open or shorted to ground.
    • Run crank relay coil control circuit open (including relay coil and ground).

B1380 01

Accessory voltage circuit is shorted to voltage.

B1380 06

    • Accessory voltage circuit is open.
    • Ignition 1 voltage, accessory voltage, or off/run/crank voltage circuit shorted to ground.
    • B+ circuit of the ignition switch open or shorted to ground.

B1440

BCM senses an open or short to voltage on the off/run/crank voltage circuit when both ignition accessory/run and ignition run/crank parameters are active.

BCM senses an open on the B+ circuit to the ignition switch while the engine is running. An open on the B+ circuit can be caused by a short to ground on any of the circuits listed below:

    • B+
    • Accessory voltage
    • Run/crank ignition 1 voltage BCM terminal 19, X4
    • Off/run/crank voltage

B1441 01

Off/run/crank voltage circuit is shorted to voltage.

B1441 06

Off/run/crank voltage circuit is open.

Actions Taken When the DTC Sets

    • The BCM stores DTC to memory.
    • The BCM operates in a fail-safe power mode dependent on the last valid power mode detected and the state of the engine run flag data on the serial data communications circuits.
    • The other modules on the vehicle operate in a fail-safe power mode dependent on the last valid power mode transmitted by the BCM and the state of the engine run flag on the serial data communications circuits.

Conditions for Clearing the DTC

    • A current DTC clears when the malfunction is no longer present.
    • A history DTC clears when the module ignition cycle counter reaches the reset threshold, without a repeat of the malfunction.

Diagnostic Aids

    • A short to ground in the run/crank ignition circuit of the run crank relay will cause an open fuse to the ignition switch. DTC B1428 should be current.
    • A short to ground in the accessory wake-up serial data circuit will cause an open fuse to the ignition switch. DTC U1814 should be current.
    • The power modes and controls are determined using BCM logic. Comparing the Body Control Module Power Mode data display parameters listed in Circuit/System Verification will determine if there is a power mode fault.

Reference Information

Schematic Reference

    •  Power Distribution Schematics
    •  Power Moding Schematics

Connector End View Reference

Component Connector End Views

Description and Operation

Power Mode Description and Operation

Electrical Information Reference

    •  Circuit Testing
    •  Connector Repairs
    •  Testing for Intermittent Conditions and Poor Connections
    •  Wiring Repairs

Scan Tool Reference

Control Module References for scan tool information

Circuit/System Verification

  1. Verify that the following DTCs are not set: U1814, B1428.
  2. If either of the DTCs are set, refer to Diagnostic Trouble Code (DTC) List - Vehicle.
  3. With a scan tool, access BCM, Power Mode data display list and compare all parameters listed with the corresponding ignition key position. The PMM Power Mode Parameters table below illustrates the correct state of these input parameters in correspondence to the ignition switch position. The circuits which the individual parameters are related to are in parentheses.

PMM Power Mode Parameters

Ignition Switch Position

Current Power Mode

Ign. Off/Run/Crank

(Terminal 5)

Ignition Accessory/Run

(Terminal 3)

Ignition Run/Crank

(Terminal 2)

Off Key Out

Off

Key Out/ACC

Inactive

Inactive

Off Key IN

Off

Key In/Off

Inactive

Inactive

Accessory

Accessory

Key Out/ACC

Active

Inactive

Run

Run

Run

Active

Active

Start

Crank Request

Crank

Inactive

Active

Circuit/System Testing

Important: You must perform the Circuit/System Verification before proceeding with Circuit/System Testing.

  1. Connect a test lamp between each fuse test terminal of the ignition switch B+ circuit fuse and ground. The test lamp should illuminate.
  2. If the test lamp does not illuminate, test the circuits listed below for a short to ground. If all circuits test OK, replace the BCM.
    • B+ terminal 4
    • Ignition terminal 3
    • Ignition terminal 5
    • Ignition terminal 2
    • Ignition voltage terminal BCM terminal 21, X4
  3. Disconnect the harness connector at the ignition switch.
  4. Connect a test lamp between the B+ circuit terminal 4 and ground. The test lamp should illuminate.
  5. If the test lamp does not illuminate, test the B+ circuit for an open/high resistance.

    Important: The ignition switch component test must be performed before proceeding with this test to verify the integrity of the switch.

  6. Perform the ignition switch component test. Verify the switch passes the test.
  7. If the ignition switch does not test normal, replace the ignition switch.
  8. Disconnect the X 1 harness connector at the BCM, test for less than 1.0 volt between the following circuit terminals of the BCM and ground.
  9. • Ignition terminal 4
    • Ignition terminal 2
    • Ignition terminal 21
    • Ignition terminal 14
    If greater than specified, test the circuit for a short to voltage.
  10. Test for less than 1.0 ohm between the BCM and the ignition switch on the circuits listed below:
  11. • Ignition terminal 4, X1 and ignition switch terminal 6
    • Ignition terminal 2, X1 and ignition switch terminal 5
    • Ignition terminal 21, X1 and ignition switch terminal 3
    • Ignition terminal 14, X1 and ignition switch terminal 2
    If greater than specified, test the circuit for open/high resistance
  12. If all circuits test normal, replace the BCM.

Component Testing

Ignition Switch

  1. Ignition OFF, disconnect the harness connector at the ignition switch.
  2. Verify the resistance between the terminals listed below match for each ignition switch position.
  3. If not the specified value, replace the ignition switch.

Resistance Test

Ignition Switch Position

Terminals 2 and 4

Terminals 3 and 4

Terminals 4 and 5

Terminals 4 and 6

Terminals 5 and 6

Off Key Out

Infinite

Infinite

Infinite

Infinite

Infinite

Off Key IN

Infinite

Infinite

< 5.0 ohms

Infinite

Infinite

Accessory

Infinite

< 5.0 ohms

Infinite

Infinite

Infinite

Run

< 5.0 ohms

< 5.0 ohms

Infinite

Infinite

< 5.0 ohms

Start

< 5.0 ohms

Infinite

Infinite

Infinite

1275-1325 ohms

Repair Instructions

Perform the Diagnostic Repair Verification after completing the repair.

    •  Control Module References for BCM replacement, setup, and programming
    •  Ignition and Start Switch Replacement