GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 GMC_Truck 🢒 2003 🢒 Savana 🢒 Engine 🢒 Engine Controls - 4.8L, 5.3L, and 6.0L 🢒 Intake Manifold Replacement

Removal Procedure

    Important: The intake manifold, throttle body, fuel rail, and injectors may be removed as an assembly. If not servicing the individual components, remove the manifold as a complete assembly.

  1. Remove the throttle body. Refer to Throttle Body Assembly Replacement in Engine Controls - 4.8L, 5.3L, and 6.0L.
  2. Remove the oil fill tube. Refer to Oil Level Indicator and Tube Replacement .
  3. Remove the fuel injectors. Refer to Fuel Injector Replacement in Engine Controls - 4.8L, 5.3L, and 6.0L.

    4. Object Number: 679510 Size: SH
  4. Disconnect the following electrical connectors:
    5. • Manifold absolute pressure (MAP) sensor (1)
    • Knock sensor (2)
    • Exhaust gas recirculation (EGR) valve, if equipped
  5. Remove the knock sensor harness electrical connector from the intake manifold.
  6. Set the electrical harness aside.

    7. Object Number: 679527 Size: SH
  7. If equipped, remove the following EGR pipe bolts:
    8. • Intake manifold (1)
    • Cylinder head (2)
    • Exhaust manifold (3)
  8. If equipped, remove the EGR pipe (with valve).
  9. If equipped, remove the EGR pipe gasket from the exhaust manifold.

    10. Object Number: 647793 Size: SH
  10. Remove the positive crankcase ventilation (PCV) hose (with valve).

    11. Object Number: 260159 Size: SH
  11. Remove the MAP sensor (1) from the intake manifold.

    12. Object Number: 492765 Size: SH
  12. Remove the accelerator control cable bracket bolts (1).
  13. Remove the accelerator control cable bracket (2) from the intake manifold.

    14. Object Number: 372717 Size: SH
  14. Remove the evaporative emission (EVAP) purge solenoid vent tube by performing the following:
    15. 14.1. Remove the EVAP tube end (2) from the solenoid (1).
    14.2. Squeeze the EVAP pipe quick connect fitting (3) retainer together.
    14.3. Remove the EVAP tube end (3) from the vapor pipe.

    Object Number: 389993 Size: SH
  15. Remove the EVAP purge solenoid bolt (2), solenoid (3), and isolator (1) from the intake manifold.

    16. Object Number: 642285 Size: SH
  16. Remove the intake manifold bolts.
  17. Remove the intake manifold.

    18. Object Number: 492770 Size: SH
  18. Remove the intake manifold gaskets (1) from the intake manifold.
  19. Discard the old intake manifold gaskets.
  20. Clean the gasket surfaces of the EGR pipe and the exhaust manifold, if equipped.

Installation Procedure

    Object Number: 492770 Size: SH
  1. Install new intake manifold gaskets (1) to the intake manifold.

    2. Object Number: 642285 Size: SH
  2. Install the intake manifold.
  3. Apply a 5 mm (0.20 in) band of threadlock GM P/N 12345382 (Canadian P/N 10953489) or equivalent to the threads of the intake manifold bolts.

    4. Notice: Refer to Fastener Notice in the Preface section.


    Object Number: 63222 Size: SH
  4. Install the intake manifold bolts.

    5. Tighten

    1. Tighten the intake manifold bolts a first pass in sequence to 5 N·m (44 lb in).
    2. Tighten the intake manifold bolts a final pass in sequence to 10 N·m (89 lb in).

    Object Number: 389993 Size: SH
  5. Install the EVAP purge solenoid (3), isolator (1), and bolt (2) to the intake manifold.

    6. Tighten
    Tighten the EVAP purge solenoid bolt to 10 N·m (89 lb in).


    Object Number: 372717 Size: SH
  6. Install the EVAP purge solenoid vent tube to the solenoid (1) and vapor pipe.

    7. Object Number: 492765 Size: SH
  7. Install the accelerator control cable bracket (2) to the intake manifold.
  8. Install the accelerator control cable bracket bolts (1).

    9. Tighten
    Tighten the accelerator control cable bracket bolts to 10 N·m (89 lb in).


    Object Number: 260159 Size: SH

    Important: Lightly coat the MAP sensor seal with clean engine oil before installing.

  9. Install the MAP sensor (1) to the intake manifold.

    10. Object Number: 647793 Size: SH
  10. Install the PCV hose (with valve).

    11. Object Number: 679527 Size: SH
  11. If equipped, position a new EGR pipe gasket on the exhaust manifold.
  12. If equipped, install the EGR pipe (with valve).
  13. If equipped, install the following EGR pipe bolts until snug:
    14. • Intake manifold (1)
    • Cylinder head (2)
    • Exhaust manifold (3)
  14. If equipped, tighten the EGR pipe bolts.

    15. Tighten

        • Tighten the EGR valve pipe-to-intake manifold bolts to 10 N·m (89 lb in).
        • Tighten the EGR valve pipe-to-cylinder head bolts to 50 N·m (37 lb ft).
        • Tighten the EGR valve pipe-to-exhaust manifold bolts to 30 N·m (22 lb ft).
  15. Route the electrical harness into position over the engine.

    16. Object Number: 679510 Size: SH
  16. Connect the knock sensor harness electrical connector to the intake manifold.
  17. Connect the following electrical connectors.
    18. • MAP sensor (1)
    • Knock sensor (2)
    • EGR valve, if equipped
  18. Install the fuel injectors. Refer to Fuel Injector Replacement in Engine Controls - 4.8L, 5.3L, and 6.0L.
  19. Install the oil fill tube. Refer to Oil Level Indicator and Tube Replacement .
  20. Install the throttle body. Refer to Throttle Body Assembly Replacement in Engine Controls - 4.8L, 5.3L, and 6.0L.