The following information covers the inspections and services required to retain the safety, dependability, and emission control performance of the vehicle.

Make sure any necessary repairs are completed at once. Whenever any fluids or lubricants are added to the vehicle, make sure that they are the proper ones.

For vehicles with dual wheels, inspect the dual wheel nut torque.

It is important to perform these underhood inspections at each fuel fill.

Engine Oil Level

Inspect the engine oil level and add the proper oil if necessary.

Engine Coolant Level

Inspect the engine coolant levels and add DEX-COOL® for the proper coolant mixture, if necessary.

Windshield Washer Fluid Level

Inspect the windshield washer fluid level in the windshield washer reservoir and add the proper fluid, if necessary.

Tire Inflation

Inspect tire inflation. Make sure the tires are inflated to the pressures specified on the Certification/Tire label located on the driver's door lock pillar. For more information, refer to Vehicle Certification Label .

Cassette Deck Service

Clean cassette decks. Cleaning should be done every 50 hours of tape play.

Restraint System Check

Make sure the safety belt reminder light and all of your belts, buckles, latch plates, retractors, and anchorages are working properly. Look for any other loose or damaged safety belt system parts. If you see anything that might keep am safety belt system from doing its job, have it repaired. Have any torn or frayed safety belts replaced.

Also look for any opened or broken air bag coverings, and have them repaired or replaced. The SIR system does not need regular maintenance.

Wiper Blade Check

Inspect wiper blades for wear or cracking. Replace the blade inserts that appear worn or damaged or that streak or miss areas of the windshield.

Spare Tire Check

At least twice a year, after the monthly inflation check of the spare tire determines that the spare is inflated to the correct tire inflation pressure, make sure that the spare tire is stored securely.

Push, pull, and then try to rotate or turn the tire. If it moves, use the ratchet/wheel wrench to tighten the cable.

Weatherstrip Lubrication

Silicone grease on weatherstrips will make them last longer, seal better, and not stick or squeak. Apply silicone grease with a clean cloth. During very cold, damp weather more frequent application may be required.

Automatic Transmission Check

Inspect the automatic transmission fluid level; add if needed. A fluid loss may indicate a problem. Inspect the system and repair as needed.

Key Lock Cylinders Service

Lubricate the lock cylinders with the recommended lubricant.

Body Lubrication Service

Lubricate all of the following areas:

More frequent lubrication may be required when exposed to a corrosive environment. In order to locate the proper lubricant. Refer to Fluid and Lubricant Recommendations .

Starter Switch Check

Automatic Transmission Shift Lock Control Check

Caution: When performing this check, the vehicle could move suddenly. Personal injury or property damage may result. Make sure there is enough room around the vehicle, in case the vehicle does move. Be ready to apply the regular brake immediately should the vehicle begin to move.

1. Before you start, be sure you have enough room around the vehicle. It should be parked on a level surface.

Important: Be ready to apply the regular brake immediately if the vehicle begins to move.

2. Firmly apply the parking brake.
3. With the engine off, turn the key to the RUN position, but don't start the engine.
4. Without applying the regular brake, try to move the shift lever out of PARK (P) with normal effort.
5. If the shift lever moves out of PARK (P), the vehicle needs service.

Ignition Transmission Lock Check

1. With the vehicle parked, set the parking brake.
2. Try to turn the ignition key to LOCK in each shift lever position.
3. The key should turn to LOCK only when the shift lever is in PARK (P).
4. The key should come out only in LOCK

Park Brake and Automatic Transmission PARK (P) Mechanism Check

Caution: When performing this check, the vehicle could begin to move. Personal injury or property damage may result. Make sure there is enough room in front of the vehicle, in case the vehicle begins to roll. Be ready to apply the regular brake immediately should the vehicle begin to move.

1. Ensure that the vehicle is parked on a fairly steep hill with the vehicle facing downhill.
2. Keep the regular brake firmly engaged while setting the park brake.
3. Perform the following procedure in order to test the holding ability of the park brake:

•	Ensure that the engine is running.

•	Ensure that the transmission is in the NEUTRAL (N) position.

•	Slowly remove foot pressure from the regular brake pedal.

•	Do this until the vehicle is held by the park brake only.

4. If the parking brake fails to hold the vehicle, repair the system. For shoe adjustment refer to .
5. Perform the following procedure in order to test the holding ability of the PARK (P)'s holding ability:

5.1.	Ensure that the engine is running.

5.2.	Shift to PARK (P).

5.3.	Release all of the brakes.

At least every spring, use plain water to flush any corrosive materials from the underbody. Take care to clean thoroughly any areas where mud and other debris can collect.