DTC P1860 TCC PWM Solenoid Circuit Electrical. GMC Truck Savana 1998

For 1990-2009 cars only

Makes 🢒 GMC_Truck 🢒 1998 🢒 Savana 🢒 DTC 🢒 DTC P1860 TCC PWM Solenoid Circuit Electrical

Automatic Transmission Components
Automatic Transmission Controls Schematics
OBD II Symbol Description Notice
Handling ESD Sensitive Parts Notice

Circuit Description

The Torque Converter Clutch Pulse Width Modulation Solenoid Valve (TCC PWM Sol. Valve) controls the fluid acting on the converter clutch valve. The converter clutch valve controls the TCC application and release. The solenoid attaches to the control valve body within the transmission. The solenoid receives ignition voltage through circuit 1020. The Vehicle Control Module (VCM) controls the solenoid by providing a ground path on circuit 418. Current flows through the solenoid coil according to the duty cycle (percentage of ON and OFF time). The TCC PWM Sol. Valve provides a smooth engagement of the TCC by operating during a duty cycle percent of ON time.

When the VCM detects a continuous open or short to ground in the TCC PWM Sol. Valve circuit or the TCC PWM Sol. Valve, then DTC P1860 sets. DTC P1860 is a type A DTC.

Conditions for Setting the DTC

•	The system voltage is 10-16 volts.

•	The engine speed is greater than 450 RPM for 5 seconds.

•	Not in fuel cutoff.

•	The VCM commands first gear.

•	The TCC duty cycle is less than 10% or greater than 90%.

•	All of the above conditions are met for 5 seconds and either of the following fail conditions occurs for 5 seconds:

-	The VCM commands the solenoid ON (90%) and the voltage input remains high (B+).

-	The VCM commands the solenoid OFF (0%) and the voltage input remains low (0 volt).

Action Taken When the DTC Sets

•	The VCM illuminates the Malfunction Indicator Lamp (MIL).

•	The VCM inhibits TCC engagement.

•	The VCM inhibits 4th gear if the transmission is in hot mode.

•	The VCM freezes shift adapts from being updated.

•	DTC P1860 stores in VCM history.

Conditions for Clearing the MIL/DTC

•	The VCM turns OFF the MIL after three consecutive trips without a failure reported.

•	A scan tool can clear the DTC from the VCM history. The VCM clears the DTC from the VCM history if the vehicle completes 40 warm-up cycles without a failure reported.

•	The VCM cancels the DTC default actions when the fault no longer exists and the ignition is OFF long enough in order to power down the VCM.

Diagnostic Aids

•	Inspect the wiring at the VCM, the transmission connector and all other circuit connecting points for the following conditions:

-	A bent terminal

-	A backed out terminal

-	A damaged terminal

-	Poor terminal tension

-	A chafed wire

-	A broken wire inside the insulation

-	Moisture intrusion

Corrosion

•	When diagnosing for an intermittent short or open condition, massage the wiring harness while watching the test equipment for a change.

Test Description

The numbers below refer to the step numbers on the diagnostic table.

This step tests for voltage to the solenoid.

This step tests the ability of the VCM and wiring to control the ground circuit.

This step tests the resistance of the TCC PWM Sol. Valve and the Automatic Transmission Wiring Harness Assembly (A/T Wiring Harness Assembly).

DTC P1860 TCC PWM Solenoid Valve Circuit - Electrical

Step

Action

Value(s)

Yes

Was the Powertrain On-Board Diagnostic (OBD) System Check performed?

Go to Step 2

Go to Powertrain On Board Diagnostic (OBD) System Check (4.3L) or Powertrain On Board Diagnostic (OBD) System Check (5.0L and 5.7L) in Engine Controls

Install the Scan Tool .
With the engine OFF, turn the ignition switch to the RUN position.

Important: Before clearing the DTC(s), use the scan tool in order to record the Freeze Frame and Failure Records for reference. Using the Clear Info function will erase the stored Freeze Frame and Failure Records from the VCM.

Record the DTC Freeze Frame and Failure Records, then clear the DTC(s).

Are DTCs P0740, P0753, P0758 and P0785 also set?

Go to Step 3

Go to Step 4

Inspect the TRANS fuse.
If the fuse is open, inspect circuit 1020 (PNK), the solenoids and the A/T Wiring Harness Assembly for a short to ground. Repair the circuit, the solenoids and the harness if necessary.

Refer to General Electrical Diagnosis in Wiring Systems.

Did you find a short to ground condition?

Go to Step 15

Go to Step 4

Turn the ignition OFF.
Disconnect the transmission 20-way connector (additional DTCs may set).
Install J 39775 Jumper Harness on the engine side of the 20-way connector .
With the engine OFF, turn the ignition switch to the RUN position.
Connect a lest lamp from J 39775 Jumper Harness cavity E to ground.

Is the test lamp on?

Go to Step 6

Go to Step 5

Repair the open or short to ground in ignition feed circuit 1020 (PNK) to the TCC PWM Sol. Valve.

Refer to Wiring Repairs in Wiring Systems.

Is the repair complete?

Go to Step 15

Install the test lamp from cavity E to cavity U of the J 39775 Jumper Harness.
Using the transmission output control function on the scan tool, command the TCC PWM Sol. Valve ON and OFF three times.

Does the test lamp illuminate when the TCC PWM Sol. Valve is commanded ON, and turn OFF when commanded OFF?

Go to Step 8

Go to Step 7

Inspect circuit 418 (BRN) of the engine wiring harness for an open, short to ground or short to power condition.

Refer to General Electrical Diagnosis in Wiring Systems.

Repair the circuit if necessary.

Refer to Wiring Repairs in Wiring Systems.

Did you find an open, short to ground or short to power condition?

Go to Step 15

Go to Step 9

Install the J 39775 Jumper Harness on the transmission side of the 20-way connector.
Using the J 39200 Digital Multimeter and the J 35616-A Connector Test Adapter Kit, measure the resistance between terminal E and terminal U.

Refer to the Connector End View .

Is the resistance within the specified range?

10-15 ohms

Go to Step 11

Go to Step 10

Replace the VCM.

Refer to VCM Replacement/Programming (4.3L) or VCM Replacement/Programming (5.0L and 5.7L) in Engine Controls.

Is the replacement complete?

Go to Step 15