Refer to
Cell 22: Glow Plug Controls
.
Circuit Description
A dash light (Wait To Start) is illuminated by the PCM when the glow plugs are commanded ON. When the PCM is commanding the Wait To Start lamp ON, the voltage potential of the circuit will be low (near 0 volts). When the PCM is commanding the Wait To Start lamp OFF, the voltage potential of the circuit will be high (near battery volts). The primary function of the PCM is to supply the ground for the Wait To Start lamp circuit.
Conditions for Setting the DTC
| • | Wait To Start lamp requested ON. |
| • | Voltage on Wait To Start lamp circuit high (near battery volts). |
or
| • | Wait To Start lamp requested OFF. |
| • | Voltage on Wait To Start lamp control circuit low (near 0 volts). |
Action Taken When the DTC Sets
| • | The PCM illuminates the Malfunction Indicator Lamp (MIL) on the second consecutive drive trip the diagnostic runs and fails. |
| • | The PCM records the operating conditions at the time the diagnostic fails. The first time the diagnostic fails, the Failure Records store this information. If the diagnostic reports a failure on the second consecutive drive trip, the Freeze Frame records the operating conditions at the time of failure and updates the Failure Records. |
Conditions for Clearing the MIL/DTC
| • | The PCM will turn the MIL off after three consecutive trips without a fault condition. |
| • | A History DTC will clear when forty consecutive warm-up cycles that the diagnostic does not fail (coolant temperature has risen 5°C (40°F) from start up coolant temperature and engine coolant temperature exceeds 71°C (160°F) that same ignition cycle. |
| • | Use of a Scan tool |
Diagnostic Aids
A faulty bulb or the control circuit shorted to ground will cause a P1643 to set.
Test Description
Number(s) below refer to the step number(s) on the Diagnostic Table.
-
Repeat the command as many times as necessary (when glow plugs are commanded ON by the scan tool, an internal PCM timer protects the glow plugs from damage by cycling them ON for 3 seconds and OFF for 12 seconds. After the 12 seconds has elapsed, the glow plugs can be commanded ON again).
-
If no trouble is found in the control circuit or the connection at the PCM, the PCM maybe malfunctioning, however, this is an extremely unlikely failure.
Step | Action | Value(s) | Yes | No | ||||||
|---|---|---|---|---|---|---|---|---|---|---|
1 |
Important: Before clearing any DTCs, use the scan tool Capture Info to save freeze frame and failure records for reference, as the Scan tool loses data when using the Clear Info function. Was the Powertrain On-Board Diagnostic (OBD) System Check performed? | -- | ||||||||
Does the glow plug lamp turn ON and OFF with each command? | -- | |||||||||
3 | The DTC is intermittent. If no additional DTCs are stored, refer to Diagnostic Aids. If additional DTCs were stored refer to those table(s). Are additional DTC(s) stored? | -- | Go to the Applicable DTC table | Go to Diagnostic Aids | ||||||
4 |
Is the lamp OFF? | -- | ||||||||
5 | With a fused jumper wire connected to ground, probe the Wait To Start lamp control circuit in the PCM harness connector. Is the lamp ON? | -- | ||||||||
6 | Check the connections at PCM. Was a repair performed? | -- | ||||||||
7 | The Wait To Start control circuit is shorted to ground, repair as necessary. Is the action complete? | -- | -- | |||||||
8 | Check the Wait To Start circuit for the following.
Was a repair performed? | -- | -- | |||||||
Replace the PCM. Important: The new PCM must be programmed. Refer to Powertrain Control Module Replacement/Programming . Is the action complete? | -- | -- | ||||||||
10 |
Does the Scan Tool indicate the diagnostic Passed? | -- | ||||||||
11 | Does the Scan tool display any additional undiagnosed DTCs? | -- | Go to the Applicable DTC Table | System OK |
