GM Service Manual Online
For 1990-2009 cars only

Steering Knuckle Replacement RWD

Tools Required

    • J 24319-B Steering Linkage and Tie Rod Puller
    • J 23742 Ball Joint Separator

Removal Procedure


    Object Number: 160827  Size: SH
  1. Raise the vehicle. Refer to Lifting and Jacking the Vehicle in General Information.
  2. Caution: Floor jack must remain under the lower control arm during removal and installation to retain the lower control arm in position. Failure to do so could result in personal injury.

  3. Support the lower control arm with a safety stand.
  4. Remove the tire and wheel. Refer to Tire and Wheel Removal and Installation in Tires and Wheels.
  5. Remove the wheel hub and bearing assembly. Refer to Front Wheel Hub, Bearing, and Seal Replacement .

  6. Object Number: 689102  Size: SH
  7. Remove the outer tie rod to steering knuckle retaining nut.

  8. Object Number: 643351  Size: SH
  9. Disconnect the tie rod end from the steering knuckle using J 24319-B .

  10. Object Number: 1842  Size: SH
  11. Remove the steering knuckle gasket only if the steering knuckle is being repaired or replaced.

  12. Object Number: 164993  Size: SH
  13. Remove the upper and lower control arms cotter pins and the retaining nuts.

  14. Object Number: 130902  Size: SH
  15. Remove the upper ball joint stud from the steering knuckle using J 23742 .
  16. Raise the upper control arm. Disengage the upper ball joint from the steering knuckle.

  17. Object Number: 130899  Size: SH
  18. Disconnect the steering knuckle from the lower ball joint using J 23742 .
  19. Remove the steering knuckle from the vehicle.
  20. Clean the steering knuckle with solvent, then air dry.
  21. Inspect the steering knuckle tapered holes that attach to the ball joints and the outer tie rod. Replace the steering knuckle if any of the 3 holes are out-of-round, deformed, or damaged.
  22. Inspect the spindle for wear or damage.

Installation Procedure


    Object Number: 164993  Size: SH
  1. Connect the steering knuckle to the lower ball joint. Press the steering knuckle onto the lower ball joint until the lower ball joint is fully seated.
  2. Connect the steering knuckle to the upper ball joint. Lower the upper control arm in order to seat the upper ball joint into the steering knuckle.
  3. Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

  4. Install the upper and lower ball joint retaining nuts.
  5. Tighten

        • Tighten the upper ball joint retaining nut to 83 N·m (61 lb ft).
        • Tighten the lower ball joint retaining nut to 125 N·m (90 lb ft).
  6. Install new cotter pins. Tighten the upper and lower ball joint nuts up to an additional 1/6 amount to insert the cotter pin through the nuts. Bend the cotter pin flat against the nut.
  7. Install the steering knuckle gasket, if necessary.

  8. Object Number: 689102  Size: SH
  9. Connect the outer tie rod to the steering knuckle.
  10. Install the outer tie rod retaining nut.
  11. Tighten
    Tighten the outer tie rod retaining nut to 47 N·m (35 lb ft).

  12. Install the rotor/hub assembly. Refer to Front Wheel Hub, Bearing, and Seal Replacement .
  13. Install the tire and wheel. Refer to Tire and Wheel Removal and Installation in Tires and Wheels.
  14. Remove the safety stand from the lower control arm.
  15. Lower the vehicle.
  16. Check the front wheel alignment. Refer to Wheel Alignment Measurement in Wheel Alignment.

Steering Knuckle Replacement AWD

Tools Required

    • J 24319-B Steering Linkage and Tie Rod Puller
    • J 36607 Ball Joint Separator
    • J 36605 Steering Knuckle Seal Installer

Removal Procedure

    Caution: Floor jack must remain under the lower control arm during removal and installation to retain the lower control arm in position. Failure to do so could result in personal injury.

  1. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle in General Information.
  2. Remove the tire and wheel. Refer to Tire and Wheel Removal and Installation in Tires and Wheels.
  3. Unload the torsion bar. Refer to Torsion Bar Replacement .
  4. Remove the wheel hub and bearing. Refer to Front Wheel Hub, Bearing, and Seal Replacement .

  5. Object Number: 689102  Size: SH
  6. Remove the outer tie rod cotter pin and retaining nut.

  7. Object Number: 643351  Size: SH
  8. Remove the outer tie rod from the steering knuckle using J 24319-B .

  9. Object Number: 689207  Size: SH
  10. Remove the upper ball joint cotter pin and retaining nut.
  11. Install the J 36607 to the upper ball joint and the steering knuckle.
  12. Disconnect the upper ball joint from the steering knuckle using the J 36607 .
  13. Remove the lower ball joint cotter pin and retaining nut.
  14. Using a pry bar, placed on top of the upper control arm and on the bottom of the frame, pry downward.
  15. With the aid of a helper, carefully hammer on the steering knuckle in the area of the lower ball joint stud in order to release the stud from the steering knuckle.
  16. Place a pry bar on the top of the upper control arm and on the bottom of the frame, and pry downward.
  17. With the aid of an assistant, carefully hammer on the steering knuckle in the area of the lower ball joint stud in order to release the stud from the steering knuckle.
  18. Remove the steering knuckle.
  19. Remove the seal from the steering knuckle.

Installation Procedure

  1. Install the seal into the steering knuckle using the J 36605 .

  2. Object Number: 689207  Size: SH
  3. Install the steering knuckle to the upper and lower ball joints.
  4. Install the lower ball joint to steering knuckle retaining nut.
  5. Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

  6. Install the upper ball joint to steering knuckle retaining nut.
  7. Tighten

        • Tighten the lower ball joint retaining nut to 128 N·m (95 lb ft).
        • Tighten the upper ball joint retaining nut to 98 N·m (72 lb ft).
  8. Install the new cotter pins. Tighten the nuts up to an additional 1/6 amount in order to insert the cotter pin through the upper and lower ball joint studs. Bend the cotter pin ends flat against the nut.

  9. Object Number: 689102  Size: SH
  10. Install the outer tie rod ball stud to the steering knuckle.
  11. Install the outer tie rod ball stud retaining nut.
  12. Tighten
    Tighten the outer tie rod ball retaining nut to 49 N·m (36 lb ft).

  13. Install a new cotter pin to the outer tie rod stud nut. Bend the pin ends against the nut flats.
  14. Install the hub and bearing assembly. Refer to Front Wheel Hub, Bearing, and Seal Replacement .
  15. Load the torsion bar. Refer to Torsion Bar Replacement .
  16. Install the tire and wheel. Refer to Tire and Wheel Removal and Installation in Tires and Wheels.
  17. Lower the vehicle.
  18. Check the front wheel alignment. Refer to Wheel Alignment Measurement in Wheel Alignment.